Bedienungsanleitung REMKO MKT260 (Seite 7 von 16) (Englisch)

587557

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Infrared remote control

Inserting the batteries into the remote control

Prior to initial operation, the batteries supplied with the

unit (2 type AAA batteries) must be inserted into the re-

mote control.

1. Slide off the cover of the battery slot on the back of

the remote control.

10 Display "Fan speed"

The signal lights of the display indicate the set fan

speed.

Highest fan speed: "High" signal light

Medium fan speed: "Med" signal light

Lowest fan speed: "Low" signal light

11 Display "Operating mode"

The signal lights on the display indicate the set oper-

ating mode.

"Cool" signal light = Cooling

"Dehumidifier" signal light = Dehumidifying

"Fan" signal light = Ventilating

12 Display "Tank Full"

This light indicates that the floating switch of the in-

ternal tank has switched off unit operation. The inter-

nal tank does not become full during normal opera-

tion because the exhaust fan transports the accumu-

lated and evaporated condensation to the outside

via the exhaust hose.

Proceed as follows to resume unit operation after it

has automatically been switched off due to a mal-

function:

1. Switch the unit off by pressing the “On/Off” button

and unplug it from the power supply.

2. Place a suitable container under the condensa-

tion drain of the internal tank.

The condensation drain is located at the bottom

left at the back of the unit.

3. Pull the plug from the condensation drain and

collect the water that drains out.

4. Then replace the plug.

1,5 V

2. Place the batteries in the slot making sure that the

polarity is correct.

Use the labelling in the slot.

3. Close the battery slot again.

General information

◊ The infrared remote control must be protected from

moisture.

◊ When the unit is switched on, each change in the

settings is automatically transferred to the room air

conditioner. A beep indicates that the data has been

properly received.

◊ The transmitter of the infrared remote control must

generally transfer changes to settings in the direc-

tion of the room air conditioner.

◊ The infrared remote control’s range is approx. 5 m.

◊ It is only possible for data to be properly transmitted

if there are no objects located between the transmit-

ter and the receiving unit such as doors, drapes,

blinds, etc.

◊ Never use old and used batteries at the same time!

◊ We recommend removing the batteries from the re-

mote control if the unit is taken out of operation for a

longer period of time.

Remove dead batteries immediately and replace

them with new batteries that meet quality stan-

dards because otherwise they may leak.

Remote control functions

All settings can also be made using an infrared remote

control. A description of the button functions can be

found in the “Control panel” section.

1 "On/Off” button

2 "Mode” button

3 "Fan Speed” button

4 "Timer” button

5 "Up/Down” buttons

ON/OFF Mode

Fan Speed Up

Timer Down

Keep in mind that if there is no plug or it is inserted

incorrectly, water may leak out after the unit has re-

sumed operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO MKT260 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO MKT260

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info