Bedienungsanleitung REMKO ML 355 DC (Seite 16 von 68) (Englisch)

726567

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

"TIMER ON" key

Press this key to activate the unit start delay time.

Each press of this key increases the delay time by

30 minutes. When the set time on the display

exceeds 10.0, each press of the button increases

the set time by 60 minutes. T

o deactivate the delay

time, set the time to 0.0.

"TIMER OFF" key

This key can be used to program the delayed

switch-of

f time. Each press of this key increases

the switch-off time by 30 minutes. When the set

time on the display exceeds 10.0, each press of

the button increases the set time by 60 minutes. To

deactivate the switch-off time, set the time to 0.0.

3-D swing mode

Press this key to start or stop the swing mode.

With the 2-point key

, you can adjust the horizontal

fin on the left side and the vertical fin on the right

side. Press this key once to change the angle by 6

degrees. Pressing the key for 2 seconds stops the

swing function. When the swing function is

stopped, LC appears on the display for three sec-

onds.

"FOLLOW ME" key

This key can be used to activate/deactivate the

FOLLOW ME function. In this mode, the room tem-

perature is measured on the remote control. This

sends a signal to the indoor unit every 3 minutes. If

the remote control does not send a signal to the

indoor unit for 7 minutes, this mode is automati-

cally deactivated.

"LED" key

This activates/deactivates the display on the indoor

unit.

Indicators on the LCD

13 12

Fig. 9: Indicators on the LCD

1: Mode indicator - shows the current operating

modes, including Auto ( ), Cooling ( ),

Dehumidification ( ), Heating ( ), Fan ( )

and back to Auto ( ) mode.

2: Signal transmission symbol. This symbol

appears when signals are being transmitted

from the remote control to the indoor unit.

3: ON/OFF symbol. This symbol appears when

the "ON/OFF" key is pressed. Pressing this

key again causes the indicator to go out.

4: TIMER ON symbol. This symbol appears

when TIMER ON is switched on.

5: ECO function (not available)

6: TIMER OFF symbol. This symbol appears

when TIMER OFF is switched on.

7: Battery charge status (weak)

8: Sleep symbol. This symbol appears when the

"Sleep" function is activated. Pressing this key

again causes the indicator to go out.

9: Temperature/Timer symbol. Shows the tem-

perature setting (-17°C~30°C). If "F

AN" mode

is selected, the temperature setting is not dis-

played. In Timer mode, the ON and OFF set-

tings appear for the TIMER.

10: FOLLOW ME symbol. This symbol appears

when the "Follow me" function is activated.

11: Display of ion generator active (optional)

12: Fan speed symbol. This is where the selected

fan speeds are displayed: AUTO (no indicator)

and the three fan speed settings:

(slow),

(medium) and

(fast). The fan speed is set to "Automatic"

when either "Auto" or "Dehumidification" mode

is activated.

13: Silent mode active (optional)

REMKO ML series

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO ML 355 DC Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO ML 355 DC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info