Bedienungsanleitung REMKO ML520 (Seite 17 von 24) (Englisch)

587595

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Only tools approved for use in cold conditions may

be used.

Pipe cutter, deburrer and flare tool.

Deburrer

Refrigerant pipe

Flare tool

uneven

thickness

formation

of cracks

formation

of cracks

rippled

CORRECT

6. Check that the flare has the correct shape.

7. First manually connect the refrigerant pipes with the

shut-off valves to ensure that they are in the proper

position.

8. Now tighten the bolts using 2 wrenches with a suffi-

ciently wide opening.

Use a second wrench to apply counterpressure

when tightening. (See figure)

Tighten

Wrench 1

Apply counter-

pressure

Wrench 2

If the length of the connection pipe is longer than 5

m, refrigerant must be added to the system during

initial operation.

See the “Adding refrigerant” section

Installation

The following instructions describe the installation of the

cooling cycle and the assembly of the indoor and outdoor

unit.

1. The required pipe diameters are provided in the

"Technical Data” table.

2. Begin with the installtion of the indoor unit.

3. Remove the supplied screw caps and use these for

continued assembly.

4. Before you flare the refrigerant pipes, make sure

that the screw cap is placed on the hose.

5. Work with the refrigerant pipes as shown in the

figure below.

11. Hang the indoor unit leaning

slightly to the back in the previ-

ously assembled wall mount

and press the bottom of the

unit into the mount.

Do not damage the pipes and

ensure that they are in the cor-

rect position.

12. Assemble the indoor unit in such a way that conden-

sation drainage is not blocked and air can always

flow freely in and out of the unit.

13. When assembling the unit, observe the bending radii

of the refrigerant pipes and never bend the hose in

the same place twice.

This may cause the pipe to become brittle or crack.

14. Place the refrigerant pipes between the indoor unit

and the outdoor unit.

Make sure that they are securely fastened and take

steps to recirculate the oil!

15. Install the outdoor unit with the wall or base console

onto stationery building parts approved for this pur-

pose.

Follow the installation instructions for the consoles.

16. Make sure that no structure-borne sound is transmit-

ted to parts of the building.

Structure-borne sound can be reduced through vi-

bration absorbers!

17. Now connect the refrigerant pipes to the outdoor unit

as described above.

18. Insulate both the installed refrigerant pipes and the

connector against heat.

19. Only use insulation hoses suitable for this tempera-

ture range that are sealed against diffusion.

9. If you have selected option 2 or 4 (drainage through

the wall), guide the condensation water pipe and

control line through the wall lead-through to the in-

door unit. If you also need a condensation pump, it

must be installed beforehand.

10. If, due to structural design conditions, it is not possi-

ble to guide the condensation pipe through as well,

make sure that the condensation can drain freely at

all times.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO ML520 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO ML520

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info