Bedienungsanleitung REMKO ML680 (Seite 14 von 24) (Englisch)

587594

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Assembly Instructions for

Service Personnel

Important instructions prior to installation

Ensure that the contents of the package are com-

plete and that the units have no visible damage re-

sulting from transport. Any problems must be com-

municated directly to your contract partner and the

shipping company.

Subsequent complaints will not be acknowledged.

Place the unit in its original packaging as close as

possible to the location where it will be assembled to

prevent damage from transport.

Prior to installation, check that the electrical connec-

tion values and the data on the type plate are

consistent.

Do not install the unit in the direct vicinity of objects

that emit intense heat.

Lights, etc.

Select a location to set up the unit where air can flow

freely in and out of the device.

Observe minimum distance.

Only use the swivel nuts supplied for the refrigerant

pipes. Other components can damage the thread.

Remove the protective caps of the unit connections

just before connecting the refrigerant pipes.

Make sure that the maximum length of 10 or 15 me-

ters for the refrigerant pipes is not exceeded and the

difference in height to the unit is not more than 5 or

8 meters.

The refrigerant pipes may not be bent or pressed.

Make sure that all refrigerant pipes including all con-

nectors and valves are insulated against heat and

sealed against diffusion.

Only add additional refrigerant to the system if the

length of the refrigerant pipes exceeds 5 meters.

See the “Adding refrigerant” section for the addi-

tional refrigerant amounts.

The condensation pipe must be placed at an incline

of at least 2%.

If this pipe is connected to a sewage pipe, an odour

seal must be installed the upper edge of which

may not extend beyond the lower edge of the indoor

unit.

All electrical connections must meet the relevant re-

quirements. The power supply is only connected to

the outdoor unit.

The control line to the indoor units should be laid at the

same time as the refrigerant pipes.

Make sure that the electrical lines have been prop-

erly attached in the electrical terminals.

The indoor unit and outdoor unit of the REMKO air-

conditioner have been adjusted to one another from

a technical standpoint.

The guarantee becomes null and void if third-party

components are used.

Remember that when installing and maintaining air

conditioners, high-pressure refrigerant pipes and

electrical current can pose hazards.

During unit operation, some components in the cool-

ing cycle can reach temperatures of more than

70°C.

Be especially careful when covers are removed.

Preventable installation mistakes

Make absolutely sure to follow the instructions below

when installing the indoor unit:

Place the pipes between the indoor unit and the out-

door unit and keep the length of the refrigerate pipes

as short as possible.

The shut-off valve of the refrigerant pipes may only

be opened once installation is complete.

Always secure electrical lines properly in the electri-

cal terminals.

Not doing so could cause a fire.

Seal open refrigerant pipes with suitable caps and/or

adhesives to prevent moisture penetration.

Avoid bending the pipes unnecessarily.

This minimises pressure loss in the refrigerant pipes

and guarantees that the compressor oil can flow

freely.

If the outdoor unit is mounted above the indoor unit,

you must take steps to recirculate the oil.

See section on oil recirculation.

Do not set up the unit in the direct proximity of de-

vices that emit intense heat, such as glass reflection

surfaces.

If the unit is assembled close to heat emissions, the

amount of warm air expelled by the plate fins of the out-

door unit is reduced.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO ML680 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO ML680

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info