Bedienungsanleitung REMKO MVT950 DC (Seite 12 von 28) (Englisch)

587707

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Installation instructions for qualiﬁed personnel

■

Observe the manuals for the

indoor unit and outdoor unit

when installing the entire

system.

■

Transport the unit in its original

packaging as close as possible

to the installation location. This

avoids transportation damage.

■

Check the contents of the

packaging for completeness

and check the unit for visible

transport damage.

Immediately notify any

deﬁciencies to the contractual

partner and forwarding agent.

■

Lift the unit at the corners

and not by the refrigerant or

condensation connections.

■

The refrigerant pipes (injection

and suction pipe), valves and

connections to make them

tight against vapour diffusion.

If necessary, also insulate the

condensation line.

■

Select an installation location

which allows air to freely

ﬂow through the inlet and

outlet (see section "Minimum

clearances")

■

Do not install the unit in

the immediate vicinity of

devices with intensive thermal

radiation.

Installation near thermal

radiation reduces the unit

output.

■

Only open the stop valves

for the refrigerant pipes after

installation has been fully

completed.

■

Seal off open refrigerant pipes

with suitable caps or adhesive

strips to avoid the inﬁltration

of moisture and never kink or

compress the refrigerant pipes.

■

Avoid unnecessary bends. This

minimises the pressure loss

in the refrigerant pipes and

ensures that the compressor

oil can ﬂow back without

obstruction.

■

Make special preparations

regarding the oil return if the

outdoor unit is located above

the indoor unit.

(see section Oil return

measures).

■

Add refrigerant if the basic

length of the refrigerant pipe

exceeds 5 metres.

For the quantity of additional

refrigerant, refer to chapter

"Add refrigerant".

■

Only use the union nuts for the

refrigerant pipes included in

the delivery, and remove them

shortly before connecting the

refrigerant pipes.

■

Establish all electrical

connections connections in

accordance with the relevant

DIN- and VDE standards.

■

See electrical connection

diagram Ensure the electrical

cables are properly connected

to the terminals, otherwise

there is a risk of ﬁre.

Important information

prior to commissioning

Always pay attention to the

afﬁliation of the electrical and

refrigerant pipes!

The connections of the

individual circuits may not be

mixed up.

A mistake in this area can have

fatal consequences!

CAUTION

Label the refrigerant pipes

(injection and suction pipes)

as well as the associated

electrical control lines of each

interior unit with a letter.

Only connect the lines to their

associated connections.

NOTE

Wall openings

■

The wall breakthrough must

have a diameter of min.

diameter of min. 70 mm and

a fall of 10 mm from inside to

outside for each indoor unit.

■

We recommend that the

inside of the hole is padded or

lined, e.g. using a PVC tube,

to prevent the pipes being

damaged.

(Page 11, ﬁgure 1).

■

After installation has been

completed, use a suitable

sealing compound to close

off the wall breakthrough

(responsibility of customer) .

Do not use materials containing

cement or lime!

Installation material

The outdoor unit is fastened with

4 screws and a wall bracket to the

wall or ﬁxed by a ﬂoor bracket to

the ground.

Only use ﬁxing materials

which are suitable for the

given application.

NOTE

Different refrigerant pipes are

required depending on the

cooling output of the indoor

unit.

NOTE

REMKO MVT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO MVT950 DC Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO MVT950 DC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info