Bedienungsanleitung REMKO MVW 452 (Seite 20 von 48) (Englisch)

726617

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

5 Installation Instructions

for qualified personnel

Important notes prior to installation

Observe the operating manuals for the indoor unit

and the outdoor unit when installing the entire

system.

n T

ransport the unit in its original packaging as

close as possible to the installation location.

You avoid transport damage by doing so.

n Check the contents of the packaging for com-

pleteness and check the unit for visible trans-

port damage. Report any damage immediately

to your contractual partner and the shipping

company.

n Lift the unit on the corners and not on the

refrigerant or condensate drainage connec-

tions.

n The refrigerant piping (liquid and suction pipe),

valves and connections must be insulated to

make them vapour diffusion proof. If necessary

also insulate the condensate drainage line.

n Select an installation location which allows air

to freely flow through the air inlet and outlet

(see section "Minimum clearances").

n Do not install the unit in the immediate vicinity

of devices which generate intensive thermal

radiation. Installation in the vicinity of thermal

radiation reduces the unit output.

n Install the refrigerant piping from the indoor unit

to the outdoor unit.

n Seal off open refrigerant piping with suitable

caps or adhesive strips to prevent the infiltra-

tion of moisture and never kink or compress

the refrigerant piping.

n Only use the union nuts supplied with the

refrigerant piping. These should only be

removed shortly before connecting the refrig-

erant piping.

n Install all electrical wiring in accordance with

applicable DIN and VDE standards.

n Ensure the electrical cables are properly con-

nected to the terminals. Otherwise there is a

risk of fire.

Selecting the installation location

The indoor unit is designed for horizontal wall

installation above doors. However

, it can also be

used in the upper wall area (min. 1.75 m above the

floor).

Installation materials

The indoor unit is attached to the wall by a wall

bracket and 4 screws (to be provided by the cus-

tomer).

Minimum clearances

Observe the minimum clearances to allow access

for maintenance and repair work and facilitate

optimum air distribution.

200

120

1500

120

Fig. 10: Minimum clearances (all measurements in

mm)

A: Air inlet/B: Air outlet

Connection variants

The following connection variants can be used for

the refrigerant, condensate and control lines.

Fig. 11: Connection variants

A: Outlet on the wall, right

B: Outlet through the wall, right

C: Outlet through the wall, left

D: Outlet on the wall, left

NOTICE!

The indoor units are equipped at the factory

with refrigerant piping approx. 30 cm long.

These must be bent in the appropriate connec-

tion direction! Please note that this may cause

the connection screw connection to be located

in the wall!

REMKO MVW series

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO MVW 452 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO MVW 452

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info