Bedienungsanleitung REMKO MXD200 (Seite 19 von 28) (Englisch)

587709

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Installation instructions for qualiﬁed personnel

Important notes prior to

installation

Minimum clearances

Observe the minimum clearances to

allow access for maintenance,

repair work and for

optimum air distribution.

Minimum clearances

All dimensions are given in mm

For installation of the entire sys-

tem, observe the operating instruc-

tions of the indoor unit and the

outdoor unit.

■

Transport the unit in its original

packaging as close as possible

to the installation location.

This avoids transportation dam-

age.

■

Check the contents of the

packaging for completeness

and check the unit for visible

transport damage.

Immediately notify any de-

ﬁciencies to the contractual

partner and forwarding agent.

■

Lift the unit at the corners and

not by the refrigerant or con-

densation connections.

■

The refrigerant pipes (injec-

tion and suction pipe), valves

and connections to make them

tight against vapour diffusion.

If necessary, also insulate the

condensation line.

■

Select an installation location

which allows air to freely ﬂow

through the inlet and outlet (see

section "Minimum clearances")

■

Do not install the unit in the

immediate vicinity of devices

with intensive thermal radia-

tion. Installation near sources of

thermal radiation reduces the

output of the unit.

■

Install the refrigerant pipes from

the indoor unit to the outdoor

unit.

■

Seal off open refrigerant lines

with suitable caps or adhesive

strips to avoid the inﬁltration

of moisture and never kink or

compress the refrigerant pipes.

■

Only use the union nuts for the

refrigerant pipes included in

the delivery, and remove them

shortly before connecting the

refrigerant pipes.

■

Establish all electrical connec-

tions in accordance with the rel-

evant DIN and VDE standards.

■

Always ensure electrical cables

are properly connected to the

terminals, otherwise there is

a risk of ﬁre.

■

Service openings should be pro-

vided in the suspended ceiling

to allow maintenance access to

the control box.

Installation material

The indoor unit is fastened using

a wall brace and 4 bolts (provided

by the customer).

In order to complete the installa-

tion, use the supplied installation

material. Appropriate dowels, trap-

ezoidal sheet metal supports, steel

proﬁles, ﬁxing clips for refrigerant

and condensation pipes (as well as

laying ducts) and connection ﬁt-

tings for condensation pipes must

also be provided.

Selection of the installation

location

The indoor unit is designed for

horizontal mounting in suspended

ceilings with Euroraster dimen-

sions. It can also be installed in

other types of suspended ceilings

with different dimensions.

Take into account the installation

height of the equipment.

1000

Installation

Installation may only be per-

formed by authorised specialists.

NOTE

Unit installation

The unit is mounted on four thread-

ed rods with the cover face down.

Take into account the ceiling grid

and any other installations.

1. Use the dimensions of the ceil-

ing cassette to mark the ﬁxing

points for the threaded rods on

structural parts approved to sup-

port the static load, and above

the suspended ceiling.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO MXD200 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO MXD200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info