Bedienungsanleitung REMKO PWN HK serie (Seite 4 von 24) (Englisch)

726838

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

REMKO PWN H / HK

Safety notes

The units were subjected to

extensive material, functional and

quality inspections prior to delivery.

However, dangers can emanate

from the units if they are used

improperly or not as intended by

untrained personnel.

Always observe the following

safety instructions:

■

The respective building code

regulations must be observed

as a basic rule

■ The operator is responsible for

proper unit installation, correct

electrical installation and safe

operation of the units

■

The units must be set up,

installed and operated

in such a way that no one

is endangered or stressed

by radiated heat

■ The units may only be fastened

to structures or ceilings made

of construction materials of

sufficient load bearing capacity

■

Installation, connection

of the heating medium,

connection of the electrical

system and maintenance may

only be carried out by trained,

qualified staff

■

The units may not be set

up, installed or operated

in potentially flammable

or explosive environments

■ The units must be installed away

from traffic zones and installed

by crane, for example. A safety

zone with a clearance of 1 m

must be ensured

■

The units may only be operated

in completely assembled

condition

■

Safety components (e.g.

protection grids) must not

be removed or rendered

inoperative

■

The units may only be used

as intended within the

specified output limits and with

the approved conveying media

Observe name plate!

■

The intake protective grate must

always be free of dirt and loose

objects; the unit outtake may

not be covered or closed

■

Never insert foreign objects into

the unit

■

The units may not be exposed

to direct jets of water

■

Never allow water to enter

the units

■ All electrical cables for the units

must be protected against

damage (e.g. by animals etc.)

Unit description

The units are stationary, indirectly

fuelled air heaters with Cu/

Al ﬁnned heat exchangers for

connection to a pumped hot water

network up to max. 105 °C.

The units can be installed on

the wall or ceiling.

The units can be used in heating

or cooling mode. However, cooling

mode is only possible when used

vertically (wall installation), as long

as the units are installed at a 90°

angle.

The units are equipped with

horizontal, individually adjustable

air discharge ﬁns as standard.

The units are equipped with

an axial fan, individually adjustable

air discharge ﬁns and an electrical

connection terminal box.

The units are equipped with

a 230 V/50 Hz stepless external

rotor motor as standard.

The units conform to

the fundamental health and safety

requirements of the appropriate

EU stipulations and are simple

to operate.

NOTE

Fault-free function of the units

is only guaranteed if the inlet

temperature at the unit inlet

and the pump performance are

appropriate for the selected

unit classiﬁcation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO PWN HK serie Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO PWN HK serie

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info