Bedienungsanleitung REMKO RKL220 (Seite 9 von 16) (Englisch)

587563

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Water Tank

The integrated water tank must be emptied from time to

time.

When the water tank is full, an alarm

goes on and the "FULL TANK" display

blinks.

The unit switches off automatically.

FULL TANK

1. Wait a few minutes before removing

the water tank.

In our experience, a little bit of water

always drips out of the unit.

2. Carefully remove the full water tank.

3. The contents of the tank can be

poured down a drain.

4. We recommend cleaning the tank

with a clean cloth.

Unit Shut Down

8. Reinsert the water tank properly.

9. Clean the dust filter and the unit

housing.

10. Follow the service instructions.

11. Store the unit in an upright position

away from dust and direct sun light.

12. Protect the unit from dust with a

plastic cover.

1. Switch the unit off with the "On / Off"

button.

2. Unplug the power cable after press-

ing the "On / Off" button.

This will prevent the device’s elec-

tronic system from being damaged.

1. Let the device run for approximately

2 hours in ventilation mode (FAN) to

dry the surface of the evaporator

plate fins.

This will prevent unpleasant odors

when the device is put back into op-

eration.

2. Switch the unit off with the "On / Off"

button.

3. Remove the plug from the plug

socket and secure the power cable

on the holder.

4. Make sure that the cable is not bent

and that there are no kinks.

5. Empty the water tank.

6. Remove the remaining water via the

tube to the left in the opening for the

water tank.

7. Make sure to replace the sealing cap

on the tube.

If the sealing cap is not replaced,

water may leak out.

Prior to longer idle periods

◊ Remove the dust filter.

◊ If the dust filter is only slightly dirty,

clean off the dust, for example, with

a vacuum cleaner.

◊ If the dust filter is very dirty it is to be

washed with a lukewarm soap solu-

tion (max. 40° C) and then to be

rinsed with clear water.

◊ Make sure that the dust filter is com-

pletely dry and undamaged before

you reinstall it.

In case of extreme dirt the dust filter

is to be replaced.

Cleaning the Dust Filter

The device is equipped with a dust filter. It can be opened

on the left side and removed.

Cleaning the plastic housing:

For cleaning, please use only a clean, soft, slightly

damp cloth to carefully wipe off the housing. Please ad-

here to the following instructions:

◊ Never use chemical cleaning agents or polish to

clean the device.

These can corrode the surface.

◊ Make sure that moisture does not enter the device.

Water and other liquids may never be sprayed di-

rectly into the unit.

This can damage the electrical system.

Maintenance and Service

Never use the unit without the dust filter installed!

Without a dust filter, the evaporator’s plate fins be-

come dirty and the performance of the unit suffers.



The power cable must be unplugged before any

work is done on the unit!



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO RKL220 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO RKL220

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info