Bedienungsanleitung REMKO RKL240 (Seite 7 von 16) (Englisch)

587564

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Infrared-remote control

All settings can also be made using an infrared remote

control (optional with RKL 220). A description of the but-

ton functions (see picture below) can be found in the

“Control panel” section. The remote control’s range is

approximately 5 m.

Power is provided by two 1.5 V AAA batteries. (supplied

with the remote control)

Operating Mode

Adjusting the direction of the outgoing air

The device is equipped with vertical and horizontal plate

fins that can be adjusted for various conditions.

7 "FULL-TANK" display (Water tank full)

When the water tank is full, the "FULL TANK" and

"MODE" displays blink and an alarm goes off. The

compressor automatically switches off. After the wa-

ter tank on the right side of the unit has been emp-

tied and replaced, the unit switches back to auto-

matic operation.

8 "COMP. ON" display (compressor is running)

When the compressor is started again for a second

time, a minimum of three minutes must elapse be-

forehand for safety reasons. During this time, the

"COMP ON" display blinks.

9 "TIMING ON" display

If this display is lit up, the unit will automatically be

switched on after a preset amount of time.

10 "TIMING OFF" display

If this display is lit up, the unit will automatically be

switched off after a preset amount of time.

11 Operating mode and fan setting display

This display provides information about the operat-

ing mode and the fan setting which have been se-

lected.

12 REMOTE-SENSOR (sensor remote control)

The unit receives the signals sent from the infrared

remote control (special accessory for RKL 220) via

the "REMOTE SENSOR".

POWER

on / off

THERMO

CONTROL

MODE

TIMER

AUTO

SWING

reset

set

1. Switch the unit on with the "On / Off”

button

2. Set the target temperature using the

arrow buttons.

3. Select the fan setting (AUTO, HI, MED

or LO) with the "MODE" button.

1. Set up the device in the room to be de-

humidified.

2. Do not extend the exhaust hose to the

outside.

The warm air remains in the room, thus

increasing the water absorption of the air.

3. Switch the unit on with the "On / Off”

button.

4. Set the lowest target temperature 20°C

using the arrow buttons.

5. Select the lowest fan setting LO with

the "MODE” button.

1. Switch the unit on with the "On / Off”

button.

2. Set the FAN operating mode with the

"MODE” button.

The exhaust hose does not need to be

connected in circulation mode.

1. Press the "AUTO SWING" button.

The vertical plate fins slowly move

back and forth to automatically distrib-

ute air.

2. Press the "AUTO SWING" button again

to adjust the fixed output direction.

The plate fins stay in the last position

they reached.

Never adjust the vertical plate fins

manually!

Adjusting the vertical plate fins:

1. Using the two adjustment levers,

manually adjust the horizontal plate

fins between the vertical plate fins.

Adjusting the horizontal plate fins:

Cooling

Ventilation (circulation)

Dehumidifying

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO RKL240 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO RKL240

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info