Bedienungsanleitung REMKO RKS335H (Seite 20 von 28) (Englisch)

587737

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Prior to performing any work on the unit, it must be

unplugged from the power supply and secured

against being inadvertently switched on!

Electrical Connection

For all units, the power supply must be installed on the

indoor units. The system’s fuse protection must be in

line with the technical requirements and the local condi-

tions.

Local guidelines for operation as well as the require-

ments established by local energy supply companies

must be observed for setup and initial operation.

Connecting the indoor unit

Proceed as follows to connect the lines:

1. Open the cover of the connection area of the indoor

unit.

2. Connect the power connection line of the indoor unit

to the power supply.

3. Close the customer-installed connection lines as de-

scribed below on the connection terminals of the in-

door unit.

4. Place the customer-installed connection lines to the

outdoor part.

Instructions for electrical connection

Inside the indoor units for all air-conditioning units, there

are connection terminals for the power connection and

the customer-supplied connection line.

The power connection line is already permanently wired

in the indoor unit up all air-conditioners. If the existing

power connection line is not long enough, replace it

keeping in mind the required cross-sections and termi-

nal connections.

For the RKS 350 H units, the sensor line supplied with

the unit must also be laid. If the distance to be covered

with this line is more than 10 m, the line must be length-

ened by the customer!

Electrical wiring diagram RKS 327 / 335 H AT

Condenser fan

1 2(N) 3 4

Compressor

Winter regulation mechanism

Sensor

fluid line

Condenser Condenser

Reverse

valve

M M

1 2(N) 3 4

Winter regulation mechanism

Condenser fan Compressor

Sensor

fluid line

Condenser Condenser

Reverse

valve

M M

Plug

Sensor

frost protection

Electrical wiring diagram RKS 350 H AT

Electrical wiring diagram RKS 371 H AT

Condenser fan

Compressor

Winter regulation

mechanism

Condenser

Reverse valve

Contactor

Condenser

Sensor fluid line

Sensor frost protection

Before proceeding with the connections, please read

the following instructions:

àElectrical installations may only be performed by

authorised service personnel in accordance with the

relevant regulations.

àAn all-channel main switch must be installed by the

customer in the supply line close to the indoor unit;

we recommend using a main or repair switch.

àPower for the outdoor part is supplied via the con-

nection line from the indoor unit.

àThe power supply’s cross-section is based on the

design specifications and the connection capacity of

the unit.

àThe connection lines to be installed by the customer

can be combined as follows:

RKS 327 H to RKS 350 H

A 3-wire and a 2-wire connection line or a 5-wire

connection line.

RKS 371 H

A 3-wire and a 6-wire connection line.

àIn some cases, we recommend separating the con-

trol line and the power supply line (L / N / PE) of the

outdoor part into two different lines with different

cross-sections for the units RKS 335 H to RKS 371 H.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO RKS335H Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO RKS335H

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info