Bedienungsanleitung REMKO RKS371H (Seite 15 von 28) (Englisch)

587735

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Minimum distances

The chart below indicates the minimum distances that

must be maintained to ensure that the units operate

properly.

A B C D E

RKS 327 H AT 200 900 300 100 200

RKS 335 H AT 200 900 300 100 200

RKS 350 H AT 200 1200 300 150 400

RKS 371 H AT 300 1500 300 150 600

Assembly Instructions for

Service Personnel

Important instructions prior to installation

àOnly use the swivel nuts supplied with the refrigerant

lines. Other components can damage the thread.

àThe units are only suitable for limited use in com-

puter rooms because after a power outage there is

no guarantee that the units will restart. It is also pos-

sible that they will only start again with specific set-

tings.

àThe unit-specific, maximum length of the refrigerant

line is 10 or 15 m respectively with a maximum

height difference of 5 or 8 m.

àEnsure the contents of the package are complete

and that the unit has no visible damage from trans-

port.

àAny problems must be communicated directly to

your contract partner and the shipping company.

Subsequent complaints will not be acknowledged.

àPlace the units in their original packaging as close as

possible to the location where they will be set up to

prevent damage from transport.

àDo not install the outdoor part and the indoor unit in

the direct vicinity of objects that emit intense heat.

Reflective glass surfaces, lights, etc.

àThe condensation line must be placed at an incline

of at least 2 % .

àIf this line is connected to the drainage line, an odour

seal must be installed the upper edge of which may

not extend beyond the lower edge of the indoor unit.

àPrior to installation, the electrical values must be

checked for consistency with the data on the type

plate.

àRemove the protective caps of the unit connections

just before connecting the refrigerant lines.

àAll electrical connections must meet the relevant re-

quirements.

àThe power supply is only connected to the indoor

unit. The unit-specific connection and sensor lines

leading to the outdoor part should be placed together

with the refrigerant lines.

àThe indoor unit and the outdoor part of the REMKO

air-conditioner are adjusted to one another from a

technical standpoint.

The guarantee becomes null and void if third-party

components are used .

àRemember that when installing and maintaining air

conditioners, high-pressure and electrical current

can pose hazards.

àDuring unit operation, some components in the cold

cycle can reach temperatures of more than 70 °C.

Be especially careful when covers are removed.

àThe air intake and outlet openings may not be

blocked by furniture, curtains, etc.

àThe refrigerant lines may not be bent or pressed.

àProtect open refrigerant lines from moisture with

caps or tape.

àPrevent unnecessary bends to minimise the pres-

sure loss in the refrigerant lines and ensure that the

compressor oil can recirculate properly.

àIf the outdoor part is mounted above the indoor unit,

make sure to take steps to recirculate the oil (oil ele-

vation arcs).

àSelect a location to set up the unit where air can flow

freely in and out of the device. Minimum distances

can be found in chart below

àMake sure that the electrical lines have been prop-

erly attached in the electrical terminals.

àMake sure that all refrigerant lines including all con-

nectors and valves are insulated against heat and

sealed against diffusion.

Wall lead-throughs

Wall lead-throughs are necessary to establish the con-

nection between the indoor unit and the outdoor unit.

Please observe the following:

àFor the connection line to the outdoor part, a lead-

through of at least 70 mm in diameter must be cre-

ated.

àThe lead-through must be placed at an incline of at

least 10 mm between the inside and outside.

àBefore beginning work, make sure that there are no

supply lines (water, etc.) located in the vicinity of the

wall lead-through.

àWe recommend cushioning the inside of the hole or

lining it with a PVC pipe to prevent the lines from be-

ing damaged.

àAfter assembly is complete, the wall lead-through

must be sealed with a suitable sealing compound.

Do not use any materials containing cement or lime!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO RKS371H Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO RKS371H

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info