726821
38
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
Malfunction Possible cause Checks Remedial measures Major
E03 Medium flow disturbance
Check:
- Air in the medium piping
- Open shut-off devices
- Medium pressure
- Circulation pump capacity
- Medium flow rate
- Flow monitor
- Bleed medium cycle
- Open shut-off valves
- Increase medium pressure
- Have circulation pump,
medium flow rate and
flow monitor checked by
a specialist company.
X
E07 Frost protection triggered
Is the supply temperature
greater than or less than 4°C?
Raise return flow
temperature, increase
medium flow rate, adjust
anti-freeze temperature to
the operating medium.
X
P81 Heat gas overtemperature
Check:
- Heat gas temperature (U04)
- Heat gas temperature probe,
probe resistance
- Refrigerant quantity
- Replace heat gas
temperature probe
- Fill refrigerant to operational
levels after rectifying
the cause of the problem
X
E44
Heating system dropped below
bottom operating limit
Outside temperature below
-20°C?
E21 Low voltage fuse triggered
Check:
- Voltage on R/S/T on
the inverter board
(min 300V)
Establish stable power supply
on the supply line
- Replace inverter board
E22/23 Overflow protection
Check:
- Current consumption of
the complete system
- Restart system
E24
DC bus overvoltage protection
triggered
Check:
- Voltage at R/S/T on
the inverter board
(max 500V)
- Voltage between DCP-IN
and DCN-IN on the inverter
board (max 800V)
Establish stable power supply
on the supply line
- Replace inverter board
E25
Inverter board low voltage
protection device triggered
Check:
- Voltage at R/S/T on the
inverter board
(min 210V)
- Voltage between DCP-IN
and DCN-IN on the inverter
board (min 300V)
Establish stable power supply
on the supply line
- Replace inverter board
E27 IPM overcurrent protection
Check:
Compressor current draw,
Pressure difference, high/low
pressure
- Reduce pressure difference
by raising the low pressure or
lowering the high pressure
E28 IPM overheating protection
Check:
- Function of the fan
- Air throughput
- Ensure that there is
adequate distance at the fan
inlet and outlet
- Clean the finned heat
exchanger
E30 / E31
Overheating of the control
electronics
Check:
- Function of the fan
- Air throughput
- Ensure that there is
adequate distance at the fan
inlet and outlet
- Clean the finned heat
exchanger
REMKO series RVS
38
38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für REMKO RVS DC serie 50-80-130-180 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von REMKO RVS DC serie 50-80-130-180

REMKO RVS DC serie 50-80-130-180 Bedienungsanleitung - Deutsch - 44 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info