Bedienungsanleitung REMKO RXT 1055 DC (Seite 22 von 84) (Englisch)

726587

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

5 Installation instructions for qualified personnel

5.1 Important notes

prior to installation

n T

ransport the unit in its original packaging as

close as possible to the installation location.

You avoid transport damage by doing so.

n Check the contents of the packaging for com-

pleteness and check the unit for visible trans-

port damage. Report any damage immediately

to your contractual partner and the shipping

company.

n Lift the unit on the corners and not on the

refrigerant or condensate drainage connec-

tions.

n The refrigerant piping (injection and suction

pipe), valves and connections must be insu-

lated against vapour density. If necessary also

insulate the condensate drainage line.

n Select an installation location which allows air

to freely flow through the air inlet and outlet

(see section "Minimum clearances").

n Do not install the unit in the immediate vicinity

of devices which generate intensive thermal

radiation. Installation in the vicinity of thermal

radiation reduces the unit output.

n Only open the shut-off valves on the refrigerant

piping after installation is complete.

n Seal off open refrigerant piping with suitable

caps or adhesive strips to prevent the infiltra-

tion of moisture and never kink or compress

the refrigerant piping.

n Avoid unnecessary bends. This minimises the

pressure loss in the refrigerant piping and

ensures that the compressor oil can flow back

without obstruction.

n Make special preparations regarding the oil

return if the outdoor unit is located above the

indoor unit (see section "Oil return measures").

n Add refrigerant if the basic length of the refrig-

erant piping exceeds 5 metres. For the quantity

of additional refrigerant, refer to chapter

"Adding refrigerant".

n Perform all electrical wiring in accordance with

applicable DIN and VDE standards.

n Ensure the electrical cables are properly con-

nected to the terminals. Otherwise there is a

risk of fire.

n Use suitable fastening materials for the instal-

lation location of the units.

5.2 Selection of installation

location

Indoor unit

The indoor unit is designed for horizontal wall

installation underneath windows. However

, it can

also be used in the upper wall area (max. 1.25 m

above the floor). The unit is also designed for hori-

zontal ceiling installation. Observe the condensate

drainage in particular here.

Fig. 19: Horizontal positioning

Outdoor unit

The outdoor unit is designed for horizontal installa-

tion on a base in outdoor areas. The installation

site must be level, flat and firm. The unit should

also be secured to prevent it from tipping over

. The

outdoor unit can be set up outside as well as inside

a building. For external installation, please observe

the following notes to protect the unit from the

influence of the weather.

Rain

For floor or roof set-up, the unit should be installed

with at least 10cm ground clearance. A floor

bracket is available as an optional accessory.

Sun

The condenser on the outdoor unit emits heat.

Exposure to sunlight further increases the temper-

ature of the fins and reduces the heat released by

the finned heat exchanger. The outdoor unit should

be installed on to the north side of the building

whenever possible. If necessary, take measures to

provide sufficient shade (responsibility of cus-

tomer). One possible solution is to build a small

roofed area over the unit. These measures should

not affect the flow of warm outlet air.

REMKO RXT series

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO RXT 1055 DC Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO RXT 1055 DC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info