Bedienungsanleitung REMKO RXT1401 DC (Seite 19 von 56) (Englisch)

587837

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

The units are factory filled with

dry nitrogen to check for leaks.

The pressurised nitrogen is

released when the union nuts

are loosened.

CAUTION

Connecting the refrigerant pipes

The on-site connection of the

refrigerant pipes is carried out on

the right side of the units.

It may be necessary to ﬁt

a reducer or ﬂared adapter to the

indoor unit. These ﬁttings are

included with the indoor unit as

an accessory kit. Once installed,

the connections must be insulated

to prevent vapour diffusion.

Refrigerant pipe

Deburrer

6 Deburring the refrigerant pipe

Unit installation

Wall installation

The unit is attached by means of

a wall bracket, taking account of

the air outlet side located towards

the top of the unit.

Ceiling installation

The unit is attached by means

of the integrated ceiling bracket,

taking account of the air outlet

side, which is located on the front

of the unit.

1. Mark the mounting points on

the structurally permissible

building sections according

to the dimensions of the wall

bracket.

2. Remove the housing's break

out opening if necessary.

3. Hook the unit on to the

previously attached bracket.

4. Connect the refrigerant pipes,

electrical cables and condensate

line to the indoor unit as

described below.

5. Check again that the unit is level.

1. Mark the mounting points on

the structurally permissible

building sections according to

the dimensions of the ceiling

bracket.

2. Remove the housing's break

out opening if necessary.

3. Hook the unit onto the four

previously installed screws/

threaded rods.

4. Fit the unit such that it is

attached 5 mm lower in the

connection area (air intake)

than on the air outlet side!

5. Connect the refrigerant

pipes, electrical cables and

condensation pipe to the indoor

unit as described below.

3. Before ﬂanging the refrigerant

pipes, ensure that the union nut

is ﬁtted on the pipe.

4. Prepare the refrigerant pipes as

shown below (Fig. 6+7).

5. Verify that the shape of the

ﬂange is correct (Fig. 8).

6. First connect and hand-tighten

the refrigerant connections

to ensure they are correctly

seated.

7. Now fully tighten the ﬁttings

using 2 suitably sized open-

ended spanners. Use one

spanner to counter the force

when tightening the ﬁtting

(Fig. 9).

8. Use only diffusion-tight

insulation hoses designed for

this temperature range.

9. Route the refrigerant pipes from

the indoor unit to the outdoor

component. Ensure that they

are adequately fastened and

take measures for the oil return,

if necessary!

The following instructions describe

the installation of the refrigerant

circuit and the assembly of the

indoor unit and the outdoor

component.

The required pipe diameters are

given in the table "Technical

data".

2. Remove the factory-ﬁtted

protective caps and union nuts

on the connections and use

these during installation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO RXT1401 DC Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO RXT1401 DC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info