Bedienungsanleitung REMKO RXT681 DC (Seite 18 von 56) (Englisch)

587835

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

■

Observe the manuals for the

indoor unit and outdoor unit

when installing the entire

system.

■

Transport the unit in its original

packaging as close as possible

to the installation location.

This avoids transportation

damage.

■

Check the contents of the

packaging for completeness

and check the unit for visible

transport damage.

Immediately notify the

contractual partner and the

forwarding agent of any

deﬁciencies.

■

Lift the unit at the corners

and not by the refrigerant or

condensation connections.

■

The refrigerant pipes

(injection and suction pipe),

valves and connections must

be insulated against vapour

diffusion. If necessary, also

insulate the condensate line.

■

Select an installation location

which allows air to freely

ﬂow through the intake and

outlet (see section "Minimum

clearances").

■

Do not install the unit in the

immediate vicinity of devices

which generate intensive

thermal radiation (installation

near sources of thermal

radiation reduces the output of

the unit).

■

Only open the shut-off valves

for the refrigerant pipes after

installation has been fully

completed.

■

Seal off open refrigerant pipes

with suitable caps or adhesive

strips to avoid the inﬁltration of

moisture and never kink or

compress the refrigerant pipes.

■

Only use the union nuts for the

refrigerant pipes included in

the delivery, and remove them

shortly before connecting the

refrigerant pipes.

■

Establish all electrical

connections connections in

accordance with the relevant

DIN- and VDE standards.

■

Always ensure the electrical

cables are properly connected

to the terminals.

Otherwise there is a risk of ﬁre.

Installation materials

The interior unit is attached to

the wall using a wall bracket

and 4 screws (provided by the

customer). 4 key head screws or

threaded rods are required for

ceiling installation.

Selection of the installation

location

The indoor unit is designed

for horizontal wall installation

underneath windows. However,

it can also be used in the upper

wall area (max. 1.25 m above the

ﬂoor). The unit is also designed to

be mounted horizontally on the

ceiling. In this case, condensate

drainage is particularly important.

Important information

prior to installation

Installation

Installation may only be

performed by authorised

specialists.

NOTE

Connection variants

The following connection variants

can be used for the refrigerant,

condensate and control lines.

Horizontal positioning

Connection variants

Refrigerant

pipes

1 Outlet on the wall, right

2 Outlet through the wall, right

3 Outlet on the wall, down

Preparations for installation

Removing the air intake grill

1. Fold the air intake grill

forwards.

2. Remove the central grill

retainer by releasing the two

bars from their fastenings.

3. Undo the lateral fastening

screws and remove the grill.

4. After successful installation, all

parts which were removed must

be ﬁtted again.

REMKO RXT...DC

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO RXT681 DC Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO RXT681 DC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info