Bedienungsanleitung REMKO SV681 (Seite 17 von 32) (Englisch)

587853

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Installation instructions for qualiﬁed personnel

■

Transport the unit in its original

packaging as close as possible

to the installation location.This

avoids transportation damage.

■

Check that the packaged

contents are complete and

inspect the unit for any visible

signs of transportation damage.

Immediately notify any

deﬁciencies to the contractual

partner and forwarding agent.

■

Lift the unit by its corners

and not the refrigerant or

condensation connections.

■

Insulate the refrigerant pipes

(injection and suction pipe),

valves and connections to make

them tight against vapour

diffusion.If necessary also

insulate the condensation pipe.

■

Select an installation location

which allows air to freely

ﬂow through the inlet and

outlet.(see section "Minimum

clearances").

■

Do not install the unit

adjacent to any hotspots.Unit

performance will be impaired if

installed next to hotspots.

■

Only open the stop valves

for the refrigerant pipes after

installation has been fully

completed.

■

Use caps or adhesive tape to

seal off the open refrigerant

pipes and prevent the ingress of

humidity.

Never kink or push in the

refrigerant.

■

Avoid unnecessary bending.

This minimises the pressure

loss in the refrigerant pipes and

ensures that the compressor

oil can ﬂow back without

obstruction.

■

Special measures concerning

the oil return pipe must be

taken if the outdoor component

is mounted above the indoor

unit.

(See section "Oil return

measures").

■

Add refrigerant if the basic

length of the refrigerant pipe

exceeds 5 metres.

The amount of additional

refrigerant is given in the

chapter "Adding refrigerant".

■

Only use the union nuts

supplied with the refrigerant

pipes. These should only

be removed shortly before

connecting the refrigerant

pipes.

■

Establish all electrical

connections in accordance with

the relevant DIN- and VDE

standards.

■

Connect the electrical cables

properly to the terminals.

Otherwise there is a risk of ﬁre.

■ Service openings should be

provided in the suspended

ceiling to allow maintenance

access to the control box.

■ Any ventilation ducts or pipes

and connection fittings, which

are used to connect a second

room or supply fresh air, should

be insulated with diffusion-tight

material.

Wall breakthroughs

■

The wall breakthrough must

have a diameter of min. 70 mm

and a fall of 10 mm from inside

to outside for each indoor unit.

■

We recommend that the

inside of the hole is padded or

lined, e.g. using a PVC tube,

to prevent the pipes being

damaged.

■

After installation has been

completed, use a suitable

sealing compound to close

off the wall breakthrough

(responsibility of customer).

Do not use cement- or lime-

based materials!

Important points prior to

installation

Control cable

Condensation pipe

Injection pipe

Suction pipe

PVC tube

Pipes and cables in wall breakthrough

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO SV681 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO SV681

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info