Bedienungsanleitung REMKO SV681 (Seite 27 von 32) (Englisch)

587853

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Functional checks and test

run

Check the following points:

■

Tightness of the refrigerant

pipes.

■

Compressor and fan running

smoothly.

■

In cooling mode, cold air should

be output by the indoor unit,

and warm air should be output

by the outdoor component.

■

Functional test of the indoor

unit and all program sequences.

■

Check the surface temperature

of the suction pipe and deter-

mine the overheating of the

vaporiser.

Measure the temperature by

holding a thermometer against

the suction pipe and subtract-

ing the boiling point tempera-

ture indicated on the pressure

gauge.

■

Record the measured tem-

peratures in the commissioning

report.

Check that the stop valves

and valve caps are tight after

carrying out any work on the

refrigerant circuit. If necessary,

use appropriate sealant

products.

NOTE

open the stop valves by turning

them anti-clockwise using a

spanner. If leaks are found,

repair the faulty connection. It

is imperative that the vacuum

creation and drying steps are

repeated!

5. Switch off the main circuit

breaker or remove the fuse

(provided by the customer).

6. Use the remote control to

switch on the unit and select

the cooling mode, maximum

fan speed and lowest target

temperature.

7. Measure and record all

the required values in the

commissioning report and

check the safety functions.

8. Check the indoor unit control

system using the functions

described in the chapter

"Operation". Timer,

temperature setting, fan speeds

and switching to ventilation or

dehumidifying mode.

9. Check the correct function

of the condensation pipe by

pouring distilled water into the

condensation tray.

A bottle with a spout is

recommended for pouring the

water into the condensation

tray.

10.Switch the indoor unit to

cooling mode.

11.Check the correct function

and settings of all regulation,

control and safety devices

during the test run.

12.Check the control system in the

indoor unit using the functions

described in the manual.

Timer, temperature settings and

all mode settings.

13.Check the overheating,

outdoor, indoor, outlet and

vaporisation temperatures and

record the measured values in

the commissioning report.

14.Switch the indoor unit to

heating mode.

15.Check all the previously

described safety devices and

functions during the test run.

16.Record the measured values in

the commissioning report.

17.Remove the pressure gauge.

Check that seals have been

ﬁtted in the sealing caps.

Final tasks

■

Re-ﬁt all the dismantled parts.

■

Instruct the operator on how to

use the equipment.

Functional test for cooling and

heating modes

1. Remove the protective caps on

the valves.

2. Start the commissioning

procedure by brieﬂy opening

the stop valves on the outdoor

component until the pressure

gauge

indicates a pressure of approx.

2 bar.

3. Use leak detection spray or

suitable devices to check that

all the connections are tight.4.

If no leaks are found, fully

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO SV681 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO SV681

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info