Bedienungsanleitung REMKO WLT-EC serie (Seite 31 von 60) (Englisch)

726826

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

5 Installation Instructions

for qualified personnel

Important notes prior to installation

Observe the operating manuals for the indoor unit

and the outdoor unit when installing the entire

system.

n Observe the operating manuals for the indoor

unit and the chiller or heating system when

installing the entire system.

n The indoor units and chillers work independ-

ently

. A connecting line between the two is not

necessary.

n Transport the unit in its original packaging as

close as possible to the installation location.

You avoid transport damage by doing so.

n Check the contents of the packaging for com-

pleteness and check the unit for visible trans-

port damage. Report any damage immediately

to your contractual partner and the shipping

company.

n Select an installation location which allows air

to freely flow through the air inlet and outlet

(see section "Minimum clearances").

n Do not install the unit in the immediate vicinity

of devices which generate intensive thermal

radiation. Installation in the vicinity of thermal

radiation reduces the unit output.

n Lift the unit at the corners and not by the

medium or condensate drainage connections.

n The medium connection lines, valves and con-

nections must have vapour density insulation.

If necessary, also insulate the condensate

drainage line. In dual systems with cooling and

heating modes, the requirements of the current

Energy Savings Ordinance (EnEV) are to be

complied with.

n Seal off open refrigerant piping with suitable

caps or adhesive strips to prevent the infiltra-

tion of moisture and never kink or compress

the refrigerant piping.

n Avoid unnecessary bends. This minimises the

pressure loss in the lines.

n Install all electrical wiring in accordance with

applicable DIN and VDE standards.

n Ensure the electrical cables are properly con-

nected to the terminals. Otherwise there is a

risk of fire.

n Service openings should be provided in the

suspended ceiling to allow maintenance

access to the control box or the valve

assembly.

Installation materials

The unit is attached to the wall bracket by 4 screws

to be provided by the customer

Selecting the installation location

The indoor unit is designed for horizontal wall

installation above doors. However

, it can also be

used in the upper wall area (min. 1.75 m above the

floor).

Minimum clearances

Observe the minimum clearances to allow access

for maintenance and repair work and facilitate

optimum air distribution.

120

200

120

1500

Fig. 27: Minimum clearances (all measurements in

mm)

1: Air inlet

2: Air outlet

Connection variants

The following connection variants can be used for

the medium and condensate pipes and the control

lines.

Fig. 28: Connection variants

A: Outlet on the wall, right

B: Outlet through the wall, right

C: Outlet through the wall, left

D: Outlet on the wall, left

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO WLT-EC serie Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO WLT-EC serie

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info