726826
43
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
9 Internal network
Up to 32 units can be operated at the same time
thanks to the parallel connection via a bus line
(accessory). The units can access this network
(internal network) at the same time.
The network can have one leading unit (master)
and up to 31 following units (slave).
The units are connected together via a two-core,
shielded bus line.
The minimum cross section is 1.0 mm
2
with a max-
imum line length of 500 m in the network (observe
the polarity!).
The end of the network must be marked by the
plugged in jumper JP1. The addresses are
assigned by adjusting the DIP switch block SW1
(see the "Configuration" chapter).
Network with infrared remote controls
n The standard infrared remote control operates
a master unit. All slave units are set according
to the programming.
n The infrared remote control or the cabled
remote control (accessory) can be used for
user-specific operation of an individual slave
unit.
Implementation
n Address assignment for the units is carried out
by changing the DIP switch settings for DIP
switch block SW1.
Network with cabled remote controls
n The cabled remote control that is available as
an accessory operates a master unit. All slave
units with cabled remote control can be pro-
grammed individually from the master unit
directly or as a complete group.
n The cabled remote control (accessory) can be
used for user-specific operation of an individual
slave unit.
Implementation
n The addresses for the master and slave units
are assigned by configuring the cabled remote
control (see separate installation instructions).
9
12
8
13 14
1110
ALARM
ALARM
0-10V
ON/OFF
GND
A
B
JP1
9
12
8
13 14
1110
ALARM
ALARM
0-10V
ON/OFF
GND
A
B
JP1
9
12
8
13 14
1110
ALARM
ALARM
0-10V
ON/OFF
GND
A
B
JP1
9
12
8
13 14
1110
ALARM
ALARM
0-10V
ON/OFF
GND
A
B
JP1
9
12
8
13 14
1110
ALARM
ALARM
0-10V
ON/OFF
GND
A
B
JP1
Fig. 36: Internal network wiring diagram
43
43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für REMKO WLT-EC serie wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von REMKO WLT-EC serie

REMKO WLT-EC serie Bedienungsanleitung - Deutsch - 60 seiten

REMKO WLT-EC serie Bedienungsanleitung - Holländisch - 60 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info