Bedienungsanleitung Renegade RXA1100 (Seite 9 von 32) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

700338

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

IMPORTANT NOTES PRIOR TO INSTALLATION

- This device is only suited for a 12 volt system with negative ground.

- The radiated heat while operation requires sufcient air circulation at the place of installation. It is

very important that the heatsink ns do not have contact with any metal parts or any surfaces which

could impair air circulation. The amplier may not be installed in small closed location or spaces

without air circulation (e.g. spare wheel recess or below the vehicle carpeting). We recommend the

installation in the vehicle’s trunk. Ensure sufcient protection against vibrations, dust and dirt.

- Ensure that the input and output cables are sufciently separated from the power supply cables.

Otherwise interferences may occur.

- Ensure the accessibility of the fuse and the operating elements after installation.

- The reliability and performance of the amplier depends on the quality of installation. Preferably

consult an expert to install the system, particularly if you want to install several loudspeakers.

POWER SUPPLY AND TURN-ON-CONNECTION

INTERCONNECTION

ATTENTION: Before you start with the installation, disconnect the ground connection from the vehicle’s

battery in order to prevent short circuits.

The power wiring which is usually installed in on-board car networks is not sufcient for a power amplier‘s

demands. Make sure that the power wires to GND and to the +12 V terminal has been sufciently specied. A

cable crosssection of at least 10 mm

must be used to connect the battery to the amplier‘s terminals.

First connect the GND terminal of the amplier to an appropriate ground connection at the chassis. To ensure a

good connection, residue dirt and dust from the connection point. A loose connection may cause malfunctions

or interferences noise and distortion.

Then connect the +12 V terminal of the amplier with the battery by using an appropriate cable including

an in-line fuse. This fuse should be located very close to the battery; for safety reasons not more than 30

cm away. Only insert the fuse when the installation, including the connection of the loudspeakers, has been

accomplished.

Then connect the remote turn-on-wire from the headunit with the amplier‘s REM terminal. A cable with a cross-

section of 0.5 mm

is adequate.

LOUDSPEAKER CONNECTIONS

- In 4-channel operation (i.e. one loudspeaker on each amplier channel), the impedance must

not be lower than 2 ohms for each speaker

- In bridging mode (two amplier outputs combined) the impedance must not be lower than 4 ohms

for the bridged output.

- Never connect loudspeaker cables with the ground of the chassis or the +12 V supply voltage.

If the amplier is operated with a too low impedance or incorrectly used, the entire sound system may be da-

maged. This means a warranty void in such cases.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Renegade RXA1100 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info