Bedienungsanleitung Renegade RXA1500 (Seite 10 von 32) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

700337

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

INPUT SENSITIVITY (FRONT, REAR & SW)

Turn the GAIN (Fig. 1.3, 1.6 or 1.16) controller of the amplier to the MIN position. Then turn the volume control-

ler of the head unit to 80 - 90% of its full setting. Now turn GAIN clockwise until you hear some distortion. Then

turn back the GAIN slightly until you hear a cleaner sound.

OPERATING ELEMENTS

VARIABLE HIGH PASS FILTER (FRONT & REAR)

Set the desired crossover frequency on the HPF controller (Fig. 1.3 or 1.8). Thus to that only the frequencies

above the chosen crossover frequency will be amplied. This effectively minimizes distortions and overloads

at lower frequencies. A good point to start is at 125 Hz.

PROTECTION CIRCUIT

The POWER LED (Fig. 1.9) lights up green, if the amplier is in operation.

The PROTECTION LED (Fig. 1.9) lights up red, when the amplier is overheated, or a short circuit occurs resp.

a too low impedance load is connected to the speaker outputs. If this events, the internal built-in protection

circuit shuts down the amplier automatically. The amplier should work again properly after you have solved

the problems.

VARIABLE LOW PASS FILTER (SW)

Set the desired crossover frequency by using the controller (Fig. 1.13). Thus to that only the frequencies below

the chosen crossover frequency will be amplied and the subwoofer plays more precise and efcient. A good

point to start is at 125 Hz.

VARIABLE BASS BOOST (SW)

With the controller BASS BOOST (Fig. 1.12) you are able to adjust the bass level from 0 - 12 dB. Use the

controller EQ (Fig. 1.11) to set the frequency of the boost between 40 and 60 Hz.

Attention: Use the controller BASS BOOST wisely!

AUDIO SIGNAL CABLES

When installing the audio cables between the RCA outputs of the head unit and the RCA inputs of the amplier,

the audio and power supply cables should, if possible, not be routed along the same side of the vehicle. We

recommend a separated installation, e.g. routing the power cable through the cable channel on the left side

and the audio cables through the cable channel of the vehicle on the right side or vice versa. This prevents

interferences due to crosstalk into the audio signal.

BASS LEVEL REMOTE CONTROLLER (SW)

With the included bass level cable remote controller (Fig. 1.16) you are able to adjust the bass level e.g. out

of the driver’s seat.

VARIABLE SUBSONIC FILTER (SW)

With the SUBSONIC controller (Fig. 1.14) you can adjust the lower crossover frequency, to lter the very low

frequencies to relieve the subwoofer or to generate a bandpass signal. If you don’t want to use this function,

turn the controller (Fig. 1.14) to the very left to the 10 Hz position.

NOTE: The adjusted value of the SUBSONIC (Fig. 1.14) should not be higher than the adjusted value of the

LPF controller (Fig. 1.13). Otherwise no sound will be audible.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Renegade RXA1500 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info