Bedienungsanleitung Renegade RXA550 (Seite 10 von 32) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

700339

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

AUDIO SIGNAL CABLES

WheninstallingtheaudiocablesbetweentheRCAoutputsoftheheadunitandtheRCAinputsoftheamplier,

the audio and power supply cables should, if possible, not be routed along the same side of the vehicle. We

recommend a separated installation, e.g. routing the power cable through the cable channel on the left side

and the audio cables through the cable channel of the vehicle on the right side or vice versa. This prevents

interferences due to crosstalk into the audio signal.

SIGNAL OUTPUTS TO CONNECT ADDITIONAL AMPLIFIERS

The input signal on the INPUT jacks (Fig. 1,6) will be routed in stereo to the output jacks OUTPUT (Fig. 1,5).

ThustheOUTPUTjackallowstheconnectionofaadditionalamplier.

INPUT SENSITIVITY

OPERATING ELEMENTS

TurntheGAIN(Fig.1,9)controlleroftheampliertotheMINposition.Thenturnthevolumecontrollerofthe

headunit to 80 - 90% of its full setting. Now turn GAIN clockwise until you hear some distortion. Then turn back

the GAIN slightly until you hear a cleaner sound.

VARIABLE HIGHPASS FILTER

Ifthe amplieris tobe usedfor mid-range/tweeterloudspeakers, setthe switchesCROSSOVER(Fig.1,3)

to HPF. Then set the desired cross-over frequency on the HPF controller (Fig.1,2). Thus to that only the fre-

quenciesabovethechosencross-overfrequencywillbeamplied.Thiseffectivelyminimizesdistortionsand

overloads at lower frequencies. A good point to start is at 125 Hz.

If you use loudspeakers (>20 cm) set CROSSOVER (Fig.1,3). to ”FULL”. In this case, the HPF controller are

without function (Fig.1,2).

PROTECTION CIRCUIT

ThePRT/PWRLED(Fig.1,1)litsupgreen,iftheamplierisinoperation.

ThePRT/PWRLED(Fig.1,1)litsupred,whentheamplierisoverheated,orashortcircuitoccursresp.atoo

low impedance load is connected to the speaker outputs. If this events, the internal built-in protection circuit

shutsdown theamplier automatically.Theampliershould workagain properlyafter youhave solvedthe

problems.

VARIABLE LOWPASS FILTER

If the amplier is used to drive a subwoofer, set the switch (Fig. 1,3) to „LPF“. Set the desired cross-over

frequency by using the controller (Fig. 1,4). Thus to that only the frequencies below the chosen cross-over

frequencywillbeampliedandthesubwooferplaysmoreprecisedandefcient.

SWITCHABLE BASS BOOST

SWITCHABLE TREBLE BOOST

By using the BASS BOOST switch (Fig.1,8) you are able to increase the bass enhancement by 6 or 12 dB.

Attention: Use the BASS BOOST wisely!

By using the TREBLE BOOST switch (Fig.1,7) you are able to increase the treble enhancement by 6 or 12 dB.

Attention: Use the TREBLE BOOST wisely!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Renegade RXA550 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info