Bedienungsanleitung Renkforce 1208455 (Seite 3 von 6) (Deutsch, Englisch, Holländisch)

656687

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

• If the product casing is damaged, discontinue product usage! When it is

still connected to the mains, do not touch the radio switch socket or the

connected device! First, switch off the mains socket to which the radio

switch socket is connected (switch off at the circuit breaker). Only then

can you remove the radio-controlled switch socket from the mains socket.

Take the product to a specialist workshop or dispose of it in an environ-

mentally friendly way.

Controls

OFF

A Control-LED (lights up on use of buttons)

Keypad for switching channels 1 to 4 (left column “ON” = on, right column “OFF” = off)

C Coding switch I, II, III, IV for one of the four address codes

D Battery compartment for a 12 V battery of type “23A”

E Control-LED (lights up when the mains socket on the front is activated)

F Front socket for connecting of a consumer load, with child-proof lock

G Coding switch I, II, III, IV for one of the four address codes

H Coding switch for switch channel selection 1, 2, 3, 4

I Safety plug for connection to the mains socket

Inserting/replacing the Battery

Open the battery compartment (D) on the back of the hand-held radio transmitter and

insert a 12V-battery (type “23A”) with the correct polarity (observe imprint in the bat-

tery compartment or the ﬁgure). Close the battery compartment again.

The batteries need to be replaced if the range of the hand-held radio transmitter is sig-

niﬁcantly reduced or the control-LED (A) no longer lights when the buttons are used.

Setting the Address Codes

One of the four address codes (I, II, III, IV) can be set on both the hand-held radio

transmitter and the radio-controlled switch socket. Therefore, up to four identical

radio-controlled switch sets can be operated without inﬂuencing each other.

Select one of the address codes (I, II, III, IV) on the hand-held radio transmitter via the

sliding switch (C). Set exactly the same address code on the related radio-controlled

switch socket(s); use a ﬂat screwdriver for turning the coding switch (G).

If you set a different code on the hand-held radio transmitter and the radio-

controlled switch socket, the switch socket will not react to the switching

commands on the hand-held radio transmitter!

Setting the Switching Channel of the Radio-Controlled

Switch Socket

On the back of the radio-controlled switch socket there is a further coding switch (H)

that is marked by the numbers “1”, “2”, “3” and “4”. It is used to select one of the four

switching channels (the hand-held radio transmitter has also imprinted the number

“1”, “2”, “3” and “4”) if more than one radio controlled switch socket is operated.

It is of course possible to set the same switching channel for two or more

radio controlled switch sockets. By means of this, the two radio-controlled

switch sockets are activated or deactivated by one keystroke.

Start-up, Function Test

Plug the radio-controlled switch socket (without the consumer load connected!) into

the designated earthed mains socket.

You can now test the function of the radio-controlled switch socket, by brieﬂy pressing

the respective “ON” button for the corresponding switching channel (1, 2, 3 or 4). The

red control-LED (E) on the radio-controlled switch socket lights up. The mains socket

(F) on the front is now activated; mains voltage is available and a connected consumer

load is turned on.

Brieﬂy press the “OFF” button of the switching channel and the control-LED (E) is

turned off; mains voltage at the mains socket (F) and therefore the connected con-

sumer load is turned off.

Operating Instructions

Radio-controlled switch set, 2 parts

Item no. 1208455

Intended Use

The product consists of a radio controlled main socket and a radio controlled hand-

held transmitter. By using the hand-held transmitter, consumer loads connected to the

remote controlled switch socket can be turned on or off.

All safety and operating instructions in this manual must be followed carefully. These

instructions not only protect the device but, in particular, your well-being. Please read

the entire operating manual before using the product.

This product complies with the applicable national and European requirements. All

names of companies and products are the trademarks of the respective owners. All

rights reserved.

Package contents

• 1x radio controlled main socket

• Hand-held radio transmitter

• 12 V special battery for hand-held radio transmitter

• Operating instructions

Safety Instructions

Damages due to failure to follow these operating instructions will void the

warranty/guarantee! We do not assume any liability for any resulting dam-

age!

We do not assume any liability for material and personal damage caused

by improper use or non-compliance with the safety instructions. In such

cases, the warranty/guarantee will be null and void!

• The unauthorized opening, conversion and/or modiﬁcation of this product

is not permitted for safety and approval reasons (CE).

• Do not use this product in hospitals or medical institutions. Although the

product only emits relatively weak radio signals, these may lead to the

malfunction of life-support systems. The same may also apply to other

zones.

• The radio-controlled switch socket(s) is/are designed in accordance with

protection class I. Only (a) standard mains socket(s) (230V~/50Hz with pro-

tective earth) for the public supply grid may be used as the power source

for the radio-controlled switch socket.

• The hand-held radio transmitter is powered by a 12 V battery (type “23A”).

• The product is not a toy and does not belong in the hands of children!

Therefore, be especially careful when children are around. Children might

try to push objects through the socket openings, for example. There is

danger of a life-threatening electric shock!

• The product must only be used in dry interiors, it must not get damp or wet.

Never touch the product, or the mains plug, with wet or damp hands when

trying to connect a plug to the wireless switch socket.

There is danger of a life-threatening electric shock!

• Never remove a mains plug from the radio controlled mains socket by pull-

ing the power cable. Always pull the plug from the socket, in the radio-

controlled switch socket, using the gripping surface provided on the side.

• Do not connect adaptor plugs in series!

• The device is only voltage-free when iit is disconnected from the mains

socket.

• Do not overload the radio switch socket (take note of the input power in

the technical information at the end of the operating manual!).

• Do not leave packaging material carelessly lying around, since it could

become a dangerous plaything for children.

• Handle the product with care; it can be damaged by impacts, blows, or

accidental falls, even from a low height.

Renkforce 1208455 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info