Bedienungsanleitung Respekta CH 66038-90WAM (Seite 21 von 26) (Deutsch, Englisch)

793445

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

English

User manual Cooker Hoods



Is the air taken from the kitchen being replaced by

sufficient fresh air, so that no partial vacuum is

being produced in the room?

The lighting fails to function:



Does the lamp need changing?



Has the lamp been properly fitted and seated in

the holder up to the stop?



Is the fuse blown or has the circuit breaker tripped

out?

If all the above checks fail to remedy the fault,

it is possible you have a more serious problem.

In no circumstances try to repair the

electronic/electrical components in the appliance.

Contact your Customer Service.

10. Customer Service

For technical queries concerning your appliance

please contact the customer service office of your

dealer.

Before calling the customer service please note

Model/Type of your appliance.

The type and rating plate is located inside the

appliance (remove the grease filter)

11. Installation

Before installation of the appliance

please pay regard to:



Installation of the appliance only at a convenient

place.



Check the wall / ceiling on sustainability and

resilience.



Check the routing of electrical and other

conductions in and on the wall respectively ceiling,

in order to not damage them with the drill.



Check the condition and resilience of electric

conduction.



We recommend the installation of the appliance by

a professional.

On installation, the minimum distance between the

hob and the hood must be exactly complied with (see

chapter 11.1 “Installation data“) and follow the

numbering of the steps and the additional

instructions. Execution with air exhausted outdoors

(A- see also the installation data). The vapours are

extracted via an air exhaust hose fixed to the

connector ring.

The diameter of the exhaust air hose must conform

to that of the connector ring. If a smoke non-return

valve is used or is planned, check whether it can

open and close freely after the installation of the

exhaust air hose. The extractor hood can be

fi200811

equipped with one (top) or two (top and back)

extractor openings.

The hood is normally initially fitted out for use of the

top extractor opening, as an extractor hood.

Openings not required are fitted with a plastic cover.

This plastic cover can be easily removed by turning

counterclockwise and optionally fitted to another

opening which is not required.

11.1 Installation data

Minimum distance from the lower edge of the hood

body:

to ceramic and cast cooking hobs 65 cm

to gas hob 70 cm

to hobs with coal/oil/wood firing 85 cm.

Only connect the appliance to the power

supply once it is properly installed.

11.2 Using the extractor hood as an exhaust air

hood (with air extracted to outdoors)

If the extractor hood has been fitted at the factory with

a carbon filter, this must be removed.

It is only practicable to use this when operating your

hood in circulation mode.

11.3 Converting the extractor hood to a

circulation hood

If you wish to use an appropriately fitted hood as a

circulation hood, you must mount the active carbon

filter(s) to the fan motor before using the hood.

The active carbon filter(s) is/are included in the scope

of supply with some models.

Otherwise you must obtain the active carbon filter(s)

from the supplier of your extractor hood.

You must also change your hood over to the “Filter

position“ at the device provided (lever or ball

handle) inside of the hood.

11.4. Electrical connection

Before connecting the extractor hood, check

that the voltage stated on the rating plate (V) agrees

with the supply voltage in your home.

Never install the appliance if the data on the

rating plate does not agree with your supply voltage.

You will find the rating plate inside the appliance,

behind the grease filter.

If the extractor hood is fitted with a standard

connector plug, connect this to an easily accessible

standard socket.

11.5 Mounting the carbon filter (not included

in the scope of supply)

You will find the mounting instructions for the carbon

filter in its packaging. To mount the carbon filter,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Respekta CH 66038-90WAM Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info