Bedienungsanleitung Respekta GKE144 (Seite 26 von 41) (Deutsch, Englisch)

793540

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

English GENERAL USER MANUAL REFRIGERATORS

fi210802

The user instructions apply to several models, for this

reason there may be some differences in the details

given, according to the type of the appliance.

1 Protecting the environment / advice for disposal

Packing

serves to protect the appliance during transportation

and recyclable materials have been used for packaging.

Corrugated board/cardboard (mainly from waste paper)

 shaped parts in PS (foamed CFC-free polystyrene)

 foils and bags in PE (polyethylene)

 strapping tapes in PP (polypropylene)

Please hand over all packaging to the nearest official

collection point, so that all the different materials can be

re-used or recycled as far as possible and any illegal

depositing of such materials is thus avoided.

2 Deciding where to locate your appliance

In order to avoid any damage or injury to persons or

things, the appliance should be unpacked by two

people and placed in the chosen location

Before positioning it, check that your new appliance

has no visible outer damage.

On no account should you start up your appliance if it

is damaged.

Check the appliance carefully for:

 Damage to the packaging which might indicate that

the appliance has been mishandled during

transportation.

 Damage to the outer casing

 Any visible damage to the cable / plug

If in any doubt let the customer service department

check the appliance.

It must at all costs be avoided, that any

environmentally damaging refrigerant leaks out by

starting up the appliance.

3 Installing your appliance

a) Unpack the fridge / freezer.

b) In order not to unnecessarily waste raw materials,

the handles (requiring smaller packaging) have not

been mounted onto the separate parts of the

appliance.

c) Mount the door handles and at the same time any

other enclosed parts according to the relevant

instructions enclosed separately.

d) Remove any objects from inside the appliance.

e) Carefully remove all film and adhesive tape from the

casing from the door

f) Remove any polystyrene pieces from around the

compressor (if present).

g) Remove all documents and accessories from inside

the appliance.

h) Clean the inside of the appliance with lukewarm

water and vinegar and dry it thoroughly with a soft

cloth.

Do not use washing liquids, sharp or

abrasive household products or any other

cleaning agents containing soda.

Note:

 Make sure that the pipes for the circulation of the

refrigerant are not damaged in any way during

installation of the appliance.

 The appliance must only be used for the purpose for

which it is intended.

 The appliance must be placed on a firm, level

surface. This is the only way to ensure that the

refrigerant can circulate freely and thus ensure that

your appliance will work efficiently.

 If possible, place your appliance in a cool, well

aired, dry room.

 Do not place your appliance in direct sunlight, nor in a

room at high temperature.

 Do not place your appliance in the vicinity of any

sources of direct heat such as heating, ovens, cooking

stove etc. (This would mean the compressor would

have to work harder and as a result the power

consumption would be considerably higher).

If installation near a direct heat source cannot be

avoided, we recommend fitting a suitable insulation

plate between the appliance and the heat source (do

not use asbestos), or at least the following minimum

distances must be observed:

 from a gas or electric cooker 3cm

 from a radiator or oven etc. 30 cm

 from another refrigerating appliance 2 cm

 from washing mach./dishwasher 2 cm

Do not place any appliances, such as

microwaves, toasters etc. which give off heat on the

appliance.

Never obstruct the ventilation grille (as far as available)

Always pull out the plug itself and never pull the cable

when cutting the appliance off from the mains supply.

WARNING !

Leave the appliance standing in its final position for

at least 2 – 4 hours before switching it on, so that

the circulation of the refrigerant stabilises and no

operating problems occur.

Before connecting up the appliance, make sure that

it is absolutely dry inside - especially in the corners.

Depending on its composition, the refrigerant

can be easily inflammable. The refrigerant circuit has

been hermetically sealed and has been tested many

times for possible leaks.

Any inexpert interference might well create a fire

hazard. Make sure nothing mechanically effects the

circulation of the refrigerant, nor, in particular, the

accessible parts around the compressor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Respekta GKE144 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info