Bedienungsanleitung Ricoh PJ X6181N (Seite 262 von 268) (Englisch)

639326

262

Zoom out

Zoom in

Vorherige Seite

1/268

Nächste Seite

247

10. Appendix

Common Problems & Solutions

(→ “Power/Status/Lamp Indicator” on page 245.)

Problem Check These Items

Does not turn on

or shut down

• Check that the power cord is plugged in and that the power button on the projector cabinet or the remote control

is on. (→ pages 15, 16)

• Ensure that the lamp cover is installed correctly. (→ page 177)

• Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the room

where you are presenting is particularly warm, move the projector to a cooler location.

• Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end of

its life. If so, replace the lamp. After replacing the lamp, reset the lamp hours used. (→ page 129)

• The lamp may fail to light. Wait a full minute and then turn on the power again.

• Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1700 meters

or higher. Using the projector at altitudes approximately 5500 feet/1700 meters or higher without setting to [HIGH

ALTITUDE] can cause the projector to overheat and the projector could shut down. If this happens, wait a couple

minutes and turn on the projector. (→ page 110)

If you turn on the projector immediately after the lamp is turned off, the fans run without displaying an image

for some time and then the projector will display the image. Wait for a moment.

Will turn off • Ensure that the [OFF TIMER], [AUTO POWER OFF] or [PROGRAM TIMER] is off. (→ page 113, 128)

No picture • Check if the appropriate input is selected. (→ page 18) If there is still no picture, press the INPUT button or one

of the input buttons again.

• Ensure your cables are connected properly.

• Use menus to adjust the brightness and contrast. (→ page 89)

• Ensure that the lens cover is open. (→ page 16)

• Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu. (→ page 129)

• Enter your registered keyword if the Security function is enabled. (→ page 36)

• If the HDMI input or the DisplayPort signal cannot be displayed, try the following.

- Reinstall your driver for the graphics card built in your computer, or use the updated driver.

For reinstalling or updating your driver, refer to the user guide accompanied with your computer or graphics

card, or contact the support center for your computer manufacturer.

Install the updated driver or OS on your own responsibility.

We are not liable for any trouble and failure caused by this installation.

• Both the composite video signal from each input connector as the computer, BNC, and BNC (CV), and the S-video

signal from the BNC (Y/C) Input connector are not output from HDMI OUT Connector of this projector.

• Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on

the power to the notebook PC.

In most cases the output signal from the notebook PC is not turned on unless connected to the projector before

being powered up.

* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver

or power management software.

• See also the page 249.

Picture suddenly

becomes dark

• Check if the projector is in the Forced ECO mode because of too high ambient temperature. If this is the case,

lower the internal temperature of the projector by selecting [HIGH] for [FAN MODE]. (→ page 110)

Color tone or hue is

unusual

• Check if an appropriate color is selected in [WALL COLOR]. If so, select an appropriate option. (→ page 110)

• Adjust [HUE] in [PICTURE]. (→ page 90)

Image isn’t square to

the screen

• Reposition the projector to improve its angle to the screen. (→ page 20)

• Perform [GEOMETRIC CORRECTION] when the trapezoid is distorted. (→ page 100)

Picture is blurred • Adjust the focus. (→ page 22)

• Reposition the projector to improve its angle to the screen. (→ page 20)

• Ensure that the distance between the projector and screen is within the adjustment range of the lens.

(→ page 233)

• Has the lens been shifted by an amount exceeding the guaranteed range? (→ page 236)

• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.

Should this happen, let the projector stand until there is no condensation on the lens.

Flicker appears on

screen

• Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5500

feet/1700 meters or lower. Using the projector at altitudes less than approximately 5500 feet/1700 meters and

setting to [HIGH ALTITUDE] can cause the lamp to overcool, causing the image to flicker. Switch [FAN MODE] to

[AUTO]. (→ page 110)

Image is scrolling

vertically, horizontally

or both

• Check the computer’s resolution and frequency. Make sure that the resolution you are trying to display is sup-

ported by the projector. (→ page 237)

• Adjust the computer image manually with the Horizontal/Vertical in the [IMAGE OPTIONS]. (→ page 91)

Ricoh PJ X6181N Seite 262

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ricoh PJ X6181N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info