Bedienungsanleitung Ricoh Pro L4160 (Seite 36 von 178) (Englisch)

639649

Zoom out

Zoom in

Vorherige Seite

1/178

Nächste Seite

1-18

Media

Usable media sizes and notes for handling are described.

Usable sizes of media

Caution in handling of medias

Pay attention to the followings for handling of medias.

Model Pro L4130 Pro L4160

Type of Recommended media

Thin coat paper/PET/Tarpaulin/Weatherproof PVC/Polyester cloth/

Cotton

Maximum width

1371mm 1620mm

Minimum width

210mm

Maximum printing width

1361mm 1610mm

Roll media

Thickness 0.3mm or less

*1. Some media have bad drying characteristics. Please check this beforehand.

Roll outside diameter

φ180mm and less

Roll weight

25kg and less (for small-size media holder, 25kg and less)

Roll inside diameter 3 or 2 inches

Side printed Side facing outward

Roll end treatment

The roll end is gently fixed to the core with weak-adhesive tape or weak

glue for easy removal.

• When handling media, wear the gloves.

If you touch the media with your bare hand, the media may be stained due to fingerprints or oil of your

finger. Be careful about it.

• Do not leave the media with the heater ON for a long time.

Waviness may occur on the media and it may cause media clogging.

When the pinch roller is at the lower position, even if it is for a short time, impression produced by the

pinch roller is left depending on the media material. Perform test feeding

(P.2-19) to check the

media status.

• Use media recommended by RICOH to ensure reliable, high-quality printing.

Set the heater temperature to meet the characteristics of the media.

• Set the temperature of the Pre-heater, Print heater and Post-heater according to the type and

characteristics of the media used.

Automatic temperature setting can be made on the operation panel by setting the profile on the

dedicated RIP. For setting on the RIP, refer to the instruction manual for your RIP.

• Pay attention to the expansion and contraction of the media.

Do not use media immediately after unpacking. The media can be affected by the room temperature

and humidity, and thus it may expand and contract.

The media have to be left in the atmosphere in which they are to be used for 30 minutes or more after

unpacked.

• Do not use curled media.

This may result in paper jamming.

If a regular-sized coated sheet of media is rolled and stored, the coated side has to face outside.

• Be careful to dusts on the edge face of the medium.

Some rolls have dusts contained in the package gathered on the edge surface of the roll. If you use as

it is, the drawing quality may be degraded due to nozzle missing or ink drops. Be sure to set the roll

after removing dusts adhering on the edge face of the roll.

• Use a media wider than 450 mm when performing the ink drop position correction for bidirectional

printing. Correcting the ink drop position for bidirectional printing cannot be performed on narrower

media. Use unidirectional printing in such a case. Also, select [STRONG] in the [VACUUM] setting if the

media is not securely adhered to the media transfer surface when using a media such as narrow media.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ricoh Pro L4160 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ricoh Pro L4160

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info