Bedienungsanleitung Ricoh Pro L4160 (Seite 150 von 178) (Englisch)

639649

150

Zoom out

Zoom in

Vorherige Seite

1/178

Nächste Seite

5-20

Message Cause Solution

The media is not set.

The sensor has been broken.

Set the media. ( P.2-5) If the same

error message appears again, contact

your local distributor to call for service.

The data has been received.

Press the key to perform print-

ing.

Or, perform data clear.

The ink of the ink cartridge has

been nearly used up.

Press the key to check the rel-

evant Eco-cartridge. Be careful because

it may be INK NEAR END soon.

Ink could not be supplied to the

damper.

Perform “DAMPER ( P.5-9) ” of the

maintenance. Also check the remaining

amount of ink in the Eco-cartridge.

Even if you performed this, when the

message is displayed, contact your local

distributor to call for service.

The liquid level sensor abnormality

of the damper has been detected.

Turn off the power to the machine and

turn it on after a while.

If the same error message appears

again, contact your local distributor to

call for service.

Overflow from the damper has been

detected.

Perform “DAMPER ( P.5-9) ” of the

maintenance. Also check the remaining

amount of ink in the cartridge.

Even if you performed this, when the

message is displayed, contact your local

distributor to call for service.

Though a certain amount was con-

sumed, there is no change in the

damper sensor High.

Though a certain amount was con-

sumed, there is no change in the

damper sensor Low.

To prevent settling out in the white

ink pack, this is displayed periodi-

cally.

Following the procedures, shake the

white ink cartridge. ( P.1-14)

The machine temperature is high.

Adjust the ambient temperature of the

installation place.

The machine temperature is low.

After “error 710 HEATER TEMP

ERROR” has occurred, the power is

forcibly turned off, and when you

restart it, this is displayed.

If the ERROR 710 appears again, con-

tact your local distributor to call for ser-

vice.

The specified expiration date of an

ink cartridge has passed.

The expiration date has passed.

However, you can use it until the end of

the following month.

Press the key to check the car-

tridge generating the warning.

The expiration date of an ink car-

tridge has passed (one month has

passed after the specified expiration

date).

One month has passed after the expira-

tion date. However, you can use it until

the end of this month. (The red LED

blinks.)

Press the key to check the car-

tridge generating the warning.

<LOCAL>

** NO MEDIA **

<LOCAL>

DATA REMA I N

<LOCAL>

INK NEAR END [ENT]

<LOCAL>

SUPPLY I NK :MMCCYYKK

<LOCAL>

DAMPER Se n s : MMCCYYKK

<LOCAL>

I n kOv e r f l ow : MMCCYYKK

<LOCAL>

DAMPER / H I GH :MMCCYYKK

<LOCAL>

DAMPER / LOW : MMCCYYKK

SHAKE WH I TE I NK

CARTR I DGES [ ENT ]

<LOCAL>

MachineTEMP/Hi ***

<LOCAL>

MachineTEMP/Lo ***

HEATER TEMP ERROR

POWER OFF [ ENT ]

<LOCAL>

Exp i r a t i on [ ENT ]

<LOCAL>

Expi rat ion(1M) [ENT]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ricoh Pro L4160 Seite 150

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ricoh Pro L4160

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info