288842
121
Zoom out
Zoom in
Vorherige Seite
1/132
Nächste Seite
119
Miscellaneous
5
Batteries dead, improperly
installed or missing
AC adapter not attached correctly
Card door open
No buttons touched so auto
power-off function was activated
Dead batteries
Camera operated in extremely
high or low temperature location
Camera operated in dark area
requiring frequent use of the flash
Batteries dead, improperly
installed or missing
No power, or mode dial is not set
Shutter release button only
pressed halfway
SmartMedia memory card not
formatted (initialized)
No space on SmartMedia
memory card
No space on internal memory
SmartMedia memory card not
working (service life exceeded)
Card door open
Self-timer on
Flash is charging
SmartMedia memory card contact
surface dirty
The image confirmation time is
too short.
The LCD monitor is turned OFF.
The video I/O switch is set on
[IN].
Dirty lens
Subject not in the center of the
autofocus field
Subject difficult to focus
Troubleshooting
Refer to the pointers listed below before submitting the equipment for repairs. If the
problem persists after trying the suggestions, contact the nearest Ricoh service office
listed at the back of this manual.
Power Source
Problem Cause Solution Page
Power will not
come on
Power cuts out
Battery quickly
consumed
Insert the batteries correctly or replace
them.
Attach correctly again.
Close the card door and retry starting.
Restart camera.
Replace with new batteries.
Recording and Playback
Shutter release
button pressed
but no image
recorded
Replace or reposition batteries.
Slide power on and set mode dial to [
]
Press shutter release button all the way.
Format SmartMedia memory card.
Erase unimportant files or replace
SmartMedia memory card.
Erase unimportant files
Replace SmartMedia memory card.
Ensure that card door is securely closed.
Press the self timer button to disengage
the self timer recording mode.
Wait until flash LED ceases flashing.
Clean contact surface with soft dry cloth.
Make the image confirmation time longer.
Press the DISPLAY button to turn ON the
LCD monitor, or set [LCD Initialization] to
[ON].
Set video I/O switch is set on [OUT].
Clean lens with blower or soft dry cloth.
Use focus lock
Use focus lock or switch to manual focus.
27
29
32
41
27
Problem Cause Solution Page
Autofocus is on
but camera not
focusing
27
41
48
33
32, 94
94
32
32
67
49
31
109
41, 110
81
68
68, 70
Cannot confirm
a shot picture
No image on
the LCD
monitor
121

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ricoh rdc 5000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info