Bedienungsanleitung Ridley Mountain Bike (Seite 21 von 42) (Englisch)

780476

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

6.1.3.b. Installing a Quick Release Front Wheel

(1) Rotate the quick-release lever so that it curves away from the

wheel (Fig. 11 & 13). This is the OPEN position.

(2) With the steering fork facing forward, insert the wheel between

the fork blades so that the axle sits firmly at the top of the slots that

are at the tips of the fork blades - the fork dropouts. The quick

release lever should be on the left side of the bicycle (Fig. 12 & 13).

If your bike has a clip-on type secondary retention device, engage it.

(3) Holding the quick-release lever in the OPEN position with your

right hand, tighten the tension adjusting nut with your left hand until it

is finger tight against the fork dropout (Fig. 11).

(4) While pushing the wheel firmly to the top of the slots in the fork

dropouts, and at the same time centering the wheel rim in the fork,

rotate the quick-release lever upwards and push it into the CLOSED

position (Fig. 11 & 12). The lever should be parallel to the fork blade

and curved towards the wheel.

CAUTION: If you can fully close the quick release without wrapping

your fingers around the fork blade for leverage, and the lever does

not leave a clear imprint in the palm of your hand, the tension is

insufficient. Open the lever; turn the tension adjusting nut clockwise a

quarter turn; then try again.

(5) If the lever cannot be pushed all the way to a position parallel to

the fork blade, return the lever to the OPEN position. Then turn the

tension adjusting nut counterclockwise one-quarter turn and try

tightening the lever again.

(6) Close the brake shoes; then spin the wheel to make sure that it is

centered in the frame and clears the brake shoes.

WARNING: Secondary retention devices are not a substitute for

correct quick release adjustment. Failure to properly adjust the quick

release mechanism can cause the wheel to wobble or disengage,

which could cause you to lose control and fall, resulting in serious

injury or death.

6.1.3.c. Removing a Quick Release Rear Wheel

(1) Open up the brake shoes (see Section 6.3.1, Figs. 16a, b, c and

d).

(2) Shift the rear derailleur to a high gear (the smallest, outermost

rear sprocket) and pull the derailleur body back with your right hand.

(3) Rotate the quick-release lever to the OPEN position (Fig. 11 &

13).

(4) Lift the rear wheel off the ground a few inches and, with the

derailleur still pulled back, push the wheel forward and down until it

comes out of the rear dropouts.

6.1.3.d. Installing a Quick Release Rear Wheel

(1) Shift the rear derailleur to its outermost position.

(2) Pull the derailleur body back with

your right hand.

(3) Rotate the quick-release lever to

the OPEN position. The lever should

be on the side of the wheel opposite

the derailleur and freewheel

sprockets.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ridley Mountain Bike Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info