Bedienungsanleitung Rika Como II PGI (Seite 11 von 24) (Englisch)

744658

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

|11

Prior to set up

Floor bearing capacity

Ensure that the substructure is capable of bearing the weight of the

stove prior to set-up.

Note

No modiﬁcations may be made to the ﬁring installation. This also

leads to loss of warranty and guarantee.

Floor protection

A glass, sheet steel or ceramic plate is recommended, if the ﬂoor is

combustible (wood, carpet, etc.). Please observe the respective local

regulations and rules.

Flue pipe connection

Q Flue pipes pose a particular source of hazard regarding gas leaks

and ﬁre. Get the advice of an authorised specialist company for

the layout and assembly.

Q Please observe the corresponding installation guidelines for walls

panelled with wood when connecting your ﬂue pipes to the stove.

Q Observe the formation of ﬂue gas (atmospheric inversion) and

draughts when the weather is unfavourable.

Q Infeed of too little combustion air can lead to smoke in the rooms

or to ﬂue gas leaks. Hazardous deposits in the stove and chimney

may also occur.

Q If ﬂue gas escapes, let the ﬁre burn out and check whether all the

air inlet openings are free and the ﬂue gas pipes and the stove

pipe are clean. If in doubt notify the master chimney sweep since

draught malfunctions may be connected to your chimney.

The correct chimney connection

There are several ways to connect your stove to the chimney, eg:

1) wind break, 2) chimney, 3) inspection opening

For the selection of the connection and to ensure a proper connection

between the stove and chimney, please read the guide „INSTALLING

THE STOVE“ or ask your local chimney sweep.

Stoves type 1 (BA 1):

Q Suitable for multiple occupancy. (Note the different country

regulations.)

Q These may only be operated with the combustion chamber door

closed.

Q The combustion chamber door is to be kept closed when the

stove is not in operation.

Q Fouling of the chimney i.e. deposits of highly inﬂammable materials

such as soot and tar and subsequently ﬁre in the chimney may

occur if the chimney is miscalculated and dimensioned wrong.

Q If this occurs, disconnect the mains plug. Phone the ﬁre brigade

and get yourself and other residents out of harm’s way.

Note

Your pellet stove has been tested as a room-air independent stove

according to EN14785. It can be operated room air dependent or

room air independent.

ROOM-AIR INDEPENDENT OPERATION:

The stove is certiﬁcated for type FC62x of the approval principles

for the inspection and evaluation of ambient air independent

ﬁreplaces speciﬁed by the Deutsches Institut für Bautechnik (DIBT)

(German Institute for Building Technology). Thanks to an air-tight

conﬁguration of the air supply line and ﬂue pipes the stove may be

operated in air-tight rooms and in rooms with room-air installations

(e.g. controlled ventilation and venting systems, extractors etc.).

ROOM-AIR DEPENDENT OPERATION:

In combination with room-air installations (e.g. controlled

ventilation and venting systems (extractors etc.) it must

be ensured that the stove and the room air system are

monitored and safeguarded mutually (e.g. via a differential

pressure controller). The combustion air infeed of approx.

20 m

/h must be ensured.

Please observe the respective local regulations and rules in

consultation with your master chimney sweep. For changes after

the printing of this manual, we can not assume any liability. We

reserve the right to change without notice.

Convection air conduction

Only for stoves with MultiAir

The stove is delivered with a cover on the convection air outlet to

prevent direct heat to the wall.

Operation without this cover or without attached convection pipes is

not allowed. If you do though no warranty and no liability is accepted

for damage.

Q The amount of air and temperature is designed to heat one

additional room.

Q Note the regional speciﬁc ﬁre safety regulations and clarify the

connection situation with the competent authority

Q The max. temperature of the convection air is 180° C at the air

outlet.

Q The convection air should be as short as possible.

Q Keep the number of deﬂections as small as possible.

Note

Please pay attention to the national and country-speciﬁc building

and ﬁre regulations when connecting the convection air pipes.

Installation and assembly must be performed by a trained

specialist only.

example

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rika Como II PGI Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Rika Como II PGI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info