Bedienungsanleitung Rika Filo (Seite 11 von 24) (Englisch)

744654

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

|11

4. TECHNOLOGY AND SAFETY FUNCTIONS

The technological advances in your new combi stove are the result of

years of testing and practical experience. The practical advantages

of your pellet stove are convincing:

Operating comfort

The microprocessor-controlled combustion regulation optimises

the interaction of ﬂue gas blower and screw using the current

combustion chamber temperature. This guarantees optimum

combustion and operating status.

All function can be regulated centrally using the integrated operating

unit. The intuitive graphic interface permits easy operation; all the

settings can be made quickly and simply.

Top efficiency - lowest emissions

A very great heat exchange surface together with optimum

combustion air control leads to excellent fuel utilisation.

Fine continuous pellet dosing in an optimised burner pot made of

high-quality grey cast iron leads to virtually complete combustion

with very good exhaust gas values - and this is guaranteed in every

operating phase.

Note

During operation, the ﬂame noise, pellets dropping and actuation

of the electronic components are audible due to the automatic

control.

Pressure monitoring

The negative pressure in the combustion chamber is continuously

monitored during operation. Below a deﬁned threshold, a correct

operation can not be guaranteed and the unit will switch off with the

fault message „NOT ENOUGH LOW PRESSURE“ for safety reason.

Note

After the occurrence of the error message, maintenance or

cleaning work necessarily has to be carried out! If the error occurs

again, a safe operation is no longer guaranteed, the service must

be informed immediately.

Note

If the stove is used in a habitation together with a kitchen hood or

a ventilation (WC) it might happen that the built-in pressure switch

stops the stove. If using the hood make sure that an adequate

supply of air is ensured.

Low-temperature shutdown

The unit switches off if the stove cools below a minimum temperature.

This switch-off may occur if pellet ignition is delayed.

Electrical excess current protection

The stove has a main fuse (at the rear) to protect against excess

current.

Automatic cleaning cycle

The speed of the ﬂue gas fan is increased every hour for a short

period to blow ash from the burn pot, increasing the operational

safety. The status indicator CLEAN appears on the display.

Only for stoves with turning grids:

Every 6 hours (interval adjustable) an additionally automatic big

cleaning cycle is performed. The stove stops, the automatic cleaning

tilts the grid and then re-ignites the stove. The status indicator BIG

CLEAN appears on the display continuously. The cleaning procedure

with tilting the grid is to convey ash and clinker from the burn pot

into the ash drawer.

Note

This additional function does not replace a manual cleaning

as described in CLEANING and MAINTENANCE, as this is

absolutely necessary to do regularly.

Note

Due to the turning grid there is a certain generation of noise during

the automatic cleaning cycle (START or BIG CLEAN.

Component monitoring

All the electrical components used are continuously monitored

during operation. If a component is defective or can no longer be

actuated correctly, then operation is stopped and a warning or error

message is issued (see MANUAL TOUCH DISPLAY.

Auger motor monitoring

Too long or wet pellets as well as pellets with too high dust content

(see BRIEF INFORMATION ON FUEL PELLETS) can cause

so-called “auger jammers” in the auger channel. This may also

happen if the pellets accumulate in the burn pot and the backlog

reaches into the chute. The auger motor reacts in both cases with

an increased current consumption, which causes the error message:

DISCHARGE MOTOR BLOCKED. The stove will be stopped.

Please call the customer service immediately.

Power failure (during heating)

After a brief power failure, the operating functions that were set

before the power failure, continues. If the power failure lasts longer,

the stove goes to start phase if sufﬁcient temperature or embers are

present. If the power failure lasts too long, the stove goes into the

stop phase. The ﬂue gas fan continues to burn any pellet residues

(approximately 10 minutes). Then it will restart automatically.

Power failure (during the initial stage)

After a brief power failure the boot process continues. If the power

failure lasts longer, the stove is in the stop phase. The ﬂue gas fan

continues to burn any pellet residues (approximately 10 minutes).

Then it will restart automatically.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rika Filo Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Rika Filo

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info