Bedienungsanleitung Rika Interno (Seite 11 von 20) (Englisch)

744681

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

|11

4. TECHNOLOGY AND SAFETY FUNCTIONS

The technological advances in your new combi stove are the result of

years of testing and practical experience. The practical advantages

of your pellet stove are convincing:

Operating comfort

All functions can be regulated using the integrated touch display.

The user-friendly interface permits extremely easy operation.

Top efficiency - lowest emissions

All processes in the stove are fully automated. The parameters

Q Air control

Q Temperature monitoring

Q Pellet dosing

are continuously optimised. This guarantees optimum combustion.

The result are low consumption and very good exhaust gas values

that even undercut the legally permitted limits.

Note

Due to the automated control, you may hear ﬂame ﬂuttering,

falling pellets and sounds from the activation of the electronic

components during operation.

DAR - Dynamic Air Regulation

A differential pressure sensor in the supply air system measures the

air ﬂow. The fan speed is adjusted automatically and guarantees

optimum combustion.

The air pipe of an external supply air pipe can also be monitored in

this way.

Pressure monitoring

The negative pressure in the combustion chamber is continuously

monitored during operation. Below a deﬁned threshold, a correct

operation can not be guaranteed and the unit will switch off with the

fault message „NOT ENOUGH LOW PRESSURE“ for safety reason.

Note

If the stove is used in a habitation together with a kitchen hood or

a ventilation (WC) it might happen that the built-in pressure switch

stops the stove. If using the hood make sure that an adequate

supply of air is ensured.

Overheating

A high temperature limiter (OTB) switches the stove off automatically

on overheating. The message „STOVE OVERHEATED“ appears.

Please take the measures in the manner described in „WARNING

AND ERROR MESSAGES“. The stove is ready for operation again

after acknowledging the error message at the internal unit.

Note

Maintenance and cleaning work must be performed if overheating

occurs! If this error recurs, operation without danger is no longer

guaranteed; notify customer service immediately.

Low-temperature shutdown

The unit switches off if the stove cools below a minimum temperature.

This switch-off may occur if pellet ignition is delayed.

Electrical excess current protection

The stove has a main fuse (at the rear) to protect against excess

current.

Automatic cleaning cycle

The speed of the ﬂue gas fan is increased every hour for a short

period to blow ash from the burn pot, increasing the operational

safety. The status indicator CLEAN appears on the display.

Only for stoves with turning grids:

Every 6 hours (interval adjustable) an additionally automatic big

cleaning cycle is performed. The stove stops, the automatic cleaning

tilts the grid and then re-ignites the stove. The status indicator BIG

CLEAN appears on the display continuously. The cleaning procedure

with tilting the grid is to convey ash and clinker from the burn pot

into the ash drawer.

Note

This additional function does not replace a manual cleaning as

described in CLEANING and MAINTENANCE, as this is absolutely

necessary to do regularly.

Note

Due to the turning grid there is a certain generation of noise during

the automatic cleaning cycle (START or BIG CLEAN.

Component monitoring

All the electrical components used are continuously monitored

during operation. If a component is defective or can no longer be

actuated correctly, then operation is stopped and a warning or error

message is issued see MANUAL TOUCH DISPLAY.

Auger motor monitoring

Too long or wet pellets as well as pellets with too high dust content

(see BRIEF INFORMATION ON FUEL PELLETS) can cause so-called

“auger jammers” in the auger channel. This may also happen if the

pellets accumulate in the burn pot and the backlog reaches into

the chute. The auger motor reacts in both cases with an increased

current consumption, which causes the error message: DISCHARGE

MOTOR BLOCKED. The stove will be stopped. Please call the

customer service immediately.

Power failure (during heating)

After a brief power failure, the operating functions that were set

before the power failure, continues. If the power failure lasts longer,

the stove goes to start phase if sufﬁcient temperature or embers are

present. If the power failure lasts too long, the stove goes into the

stop phase. The ﬂue gas fan continues to burn any pellet residues

(approximately 10 minutes). Then it will restart automatically.

Power failure (during the initial stage)

After a brief power failure the boot process continues. If the power

failure lasts longer, the stove is in the stop phase. The ﬂue gas fan

continues to burn any pellet residues (approximately 10 minutes).

Then it will restart automatically.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rika Interno Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Rika Interno

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info