Bedienungsanleitung Rika Look (Seite 12 von 16) (Englisch)

744637

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

6. MANUAL OPERATION

Each combustion process needs oxygen. Before ignition the combustion

chamber must be regularly cleaned from ash to ensure an adequate supply

of air.

The right ﬁll amount for heating up is 2 - 3 logs of the quantity given in amount

of fuel.

Correct heating up primarily according to instructions counteracts excessive

smoke during heating up.

Note

Pay especially attention with the wooden bench on falling out embers during

reloading! Fire hazard!

Combustion air regulation

The performance of your stove also depends on the chimney draught; therefore

the control knob for combustion air regulation must be used according to your

own experience.

Heating-up position

100% secondary air

100% primary air

Middle position

100% secondary air

0% primary air

Zero position

0% secondary air

0% primary air

The primary air intake is absolutely necessary for heating up. The “heating-up

position“ may only be used for heating up.

If the stove is not in use, warm air can release through the chimney. The zero

setting of the control knobs can largely prevent this.

RIKA firelighter

Always ignite the RIKA ﬁrelighter on the red tip. One block consists out of 8 ribs

which can be divided to the desired size. The amount of RIKA ﬁrelighters also

depends on the size and humidity of your ﬁrewood. Ideally, one rib is enough

to light up the ﬁre.

Tip

You can order the RIKA ﬁrelighter with the number E15834 at your RIKA

dealer.

Correct heating up

1. Set the control knobs to heating-up position – primary and secondary air

intakes are opened completely in the heating-up position. Place two small

pieces of chipboard lengthways left and right in the bottom of the combustion

chamber.

Place two logs crossways on top of this chipboard.

2. Now place further pieces of chipboard in crosswise layers on top of the

logs and place 2-4 ribs of the RIKA-ﬁrelighter on top of the chipboard. Some

uncoated paper can be placed underneath the chipboard in case there is no

ﬁrelighter available.

3.Now light the ﬁrelighter (or the uncoated paper) and close the combustion

chamber door.

Set the air control knobs to middle position some minutes later. The primary air

intake is now closed and the secondary air intake is completely open. Another

few minutes later (depending on draught and fuel quality / amount), the control

knob can be set further to zero setting to reduce the air intake.

After the ﬁrst burn-off, add one or two logs (see Amount of fuel) to the blaze. Set

the control knob to heating-up position again until the wood is well lit.

Please proceed in the same way for every further addition of wood.

Note

Sometimes a lot of smoke develops when wood is placed on a low ﬁrebed or

when there is too less fresh air for combustion. An explosive gas/air mixture

may arise and cause an eventual heavy deﬂagration. For safety reasons it is

recommended to leave the combustion chamber door closed and press the

control knob at the rear wall down completely into “heating-up position”. If the

log wood is not igniting, start a new heating-up procedure after it stopped

smoking.

Primary combustion air

Secondary combustion air

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rika Look Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Rika Look

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info