Bedienungsanleitung Rika Touch Display V2-14 (Seite 9 von 12) (Englisch)

744714

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

2. MODES

Note

When operating correctly, the stove may not be overheated. However

improper operation can shorten the life expectancy of electrical components

(blowers, motors and electrical control) and is not allowed!

Operation Modes Manual/Automatic/Comfort

The recommended heat output is in the range between

50% -100%. If you want to select a lower heating power, stay for about 2

seconds on the MINUS button. Then you can adjust the heat output in the range

between 30% and 50%.

Tip

Within the recommended range of 50% - 100% output the sooting of the

combustion chamber and door glass is reduced.

MANUAL MODE

The pellet burner start and stop (ON / OFF buttons) and set the desired heat

output (PLUS / MINUS buttons) can be done on the touch screen directly at the

HOME main menu.

AUTOMATIC MODE

The change from the operating status “STOVE OFF“ to STANDBY-status (ON

button) and from STANDBY-status to STOVE OFF (OFF button) is made by

pressing the screen buttons directly in the HOME - main menu. The desired heat

output (PLUS / MINUS buttons) is also set here.

The heating time program regulates the change between STANDBY-status and

CONTROL MODE automatically.

Tip

If no heating times are stored the icon „heating times“ ﬂashes and the stove

remains in standby.

The pellet burner start is within the heating times.

The pellet burner stop is outside the heating times.

In the operating status STOVE OFF no automatic pellet burner start is possible,

the system is turned off.

COMFORT MODE

The change from the operating status “STOVE OFF“ to STANDBY-status (ON

button) and from STANDBY-status to STOVE OFF (OFF button) is made by

pressing the screen buttons directly in the HOME - main menu. The desired

room temperature (PLUS / MINUS buttons) is also set here.

In the COMFORT mode heating times can be activated additionally.

The pellet burner start is within the heating times (or always with heating

times deactivated) if the actual room temperature is below the desired room

temperature. In between the heating times the pellet burner starts if the actual

room temperature is below the decreasing temperature preset or if the frost

protection is activated.

The pellet burner stops either outside the heating periods, or if the actual room

temperature is higher than the desired room temperature.

In the operating status STOVE OFF no automatic pellet burner start is possible,

the system is turned off.

Emergency operation - heating up without

electrical Ignition

If the ignition cartridge fail, ﬁrelighters can be used for an emergency operation.

First, start the stove as usual. Wait for the turning of the grid (only for units with

turning grids). Then open the combustion chamber door and give a handful

of pellets with the ﬁrelighter into the clean burn pot, light it up and close the

combustion chamber door.

Note

Do not use ﬂammable liquids to light up the ﬁre!

Convection Fan - Control

(only for devices with convection fan, except type Interno)

Settings in the Setup menu

Convection Fan

You can switch on or off the convection fans as needed.

Conv. Fan Level

The convection fan speed is adjustable from level 5 (max.) to level 1 (min.). If

you continue to press the „minus“ button, you’ll set to AUTO. The convection

fan speed will be adjusted automatically depending on the heating power (30 -

100%). This setting should be chosen as standard.

Tip for MultiAir stoves

The manually speed settings are useful if, for example, the second room

needs to be heated up quickly or heat needs to be removed from the stove.

Conv. Fan Area

You can also adapt the convection fan speed (+/- 30% fan speed). This is applied

for manual and for the AUTO setting. The fan speed can be reduced if the noise

is perceived as too loud. Conversely, for MultiAir stoves, the performance can

be increased when generally too little heated air is passed into the next room.

only for stove Domo:

Convection Fan 1 / Convection Fan 2

Here you can make the settings for both fans. They are controlled independently

(as described above)

Convection Fan - Model Interno

To prevent overheating of the stove, the convection fan in the model Interno

can not be switched off. Once the stove is in operation, the convection fan

starts for safety reasons. The „AUTO“ setting can not be changed. A fan speed

adjustment can still be made.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rika Touch Display V2-14 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Rika Touch Display V2-14

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info