Bedienungsanleitung Roadstar CLR-2560 (Seite 4 von 20) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

592294

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

English English

POWER SUPPLY

This unit operates from a main supply of 230V ~ 50Hz. Connect the AC power

cord to the AC household main outlet. Ensure that the voltage is as indicated

on the rating plate on the rear of the unit.

Battery Back-up Power Failure Protection

This radio has a battery back up circuit that will keep the correct time and

alarm settings in the event of a temporary power interruption.

Install a 9-volt battery (type 6F 22/006P), not included, into the battery

compartment located on the bottom of the unit.

Note: We recommend an alkaline battery for longer usable life. Change the

battery every 9 to 12 months for best result and avoid possible battery

leakage.

If power is temporarily interrupted the display will blink and the radio will not

play. However, the battery back-up circuit will continue to maintain the clock

and alarm settings. When power is restored the clock will display the correct

time and alarm settings, and no adjustment is necessary.

Note: If power is interrupted and there is no battery in the compartment or

the battery is exhausted. The time and alarm settings will be lost.

When power is restored the clock will begin to flash indicating that the

time and alarm settings must be corrected.

SETTING THE CORRECT TIME

1. Set the FUNCTION Selector (1) to the OFF position.

2. Press and keep pressed the TIME SET Button (14), then press the

HOUR button (9) to advance hour, press MINUTE button (13) until the

correct time is displayed.

SETTING THE WAKE UP TIME

1. Set the FUNCTION Selector (1) to the OFF position.

2. Set the alarm time by following this procedure:

3. Press and hold the ALARM SET Button (8).

4. Press the HOUR Button (9) to advance hour, press MINUTEbutton (13)

until the desired alarm time is displayed.

5. Release the ALARM SET Button (8).

6. To check the correct alarm time is set, press the ALARM SET Button (8).

WAKE TO BUZZER ALARM

1. Set the alarm time as shown above.

2. Set the Function Selector (1) to the AUTO position.

“”will appear on the left lower side of the display.

3. Turn the VOLUME Control to the desired level.

4. To switch off the alarm either press the ALARM SET (8) or set the

FUNCTION Selector (1) to the OFF position.

WAKE TO THE RADIO

1. Set the alarm time as shown above.

2. Set the FUNCTION Selector (1) to the ON position.

3. Set the FM/AUX Selector (11) to FM, and follow the procedure in

LISTENING TO THE RADIO to tune the radio to a station.

4. Set the VOLUME Control (12) to a level you feel will wake you.

5. Set the FUNCTION Selector (1) to the AUTO position. “”will appear

on the left lower side of the display.

6. To switch off the alarm either press the ALARM SET (8) or ALARM OFF

Buttons (17), or set the FUNCTION Selector (1) to the OFF position.

LISTENING TO THE RADIO

1. Set the FUNCTION Selector (1) to the ON position.

3 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roadstar CLR-2560 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info