Bedienungsanleitung Roadstar TTR-8632UCEN (Seite 7 von 32) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch)

592100

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

EnglishEnglish

ENCODING OF PHONO INTO MP3 FILE

The system is able to ENCODE music from TURNTABLE to MP3 format and recording at

memory media with USB connecting port.

REMARK:

- The recording speed is 1:1 and according to the actual plying time of the track

- The system will creat a “ AUDIO “ folder and then store the encoding track in it.

- The recording format is preset at – MP3 bit rate : 128 kbps, sampling rate : 44.1khz

- No song title will be recorded during encoding mode

- To interrupt the recroding, press the “ RECORD “ button again during record mode.

- Recording will be completed only entire song being encoded, if terminate the

encoding process intermediately, there is no track being recorded nor stored to

the USBor SD/MMC card.

COPYING OF MP3/WMA FILE FROM USB TO MMC

By pressing the “ RECORD “ button (3) the system will copy the files from to the USB to the

MMC card, and the system will switch to copying mode only if MP3/WMA file is being read.

REMARK:

- The system will store the file to USB source first if both USB and SD slot are being

occuplied by storage media.

- If press the “ Record “ button during playback of USB or SD source, the file will copy

from USB to SD or SD to USB.

A) PHONO ENCODING

1) Set the Function button to “ PHONO “ mode and then press the “ RECORD “ button (3)

directly.

2) The LCD display with show the word “ USB “ and then flashing, and then display “

“ & “ “ and flashing after few seconds. Now the system is starting the

encoding mode.

3) Start playback at PHONO for the track which you want to record to USB.

4) After finishing of recoding, press and hold the “ RECORD “ button (3) until the LCD

stops flashing and returns to “ PHONO “ mode.

B) ENCODING BITRATE (BY REMOTE HANDSET)

You can select the desired BITRATE during ENCODING from PHONO to USB, the selectable

range from 32 / 64 /96 /128 / 192 / 256 Kbps.

1) Set in “ PHONO “ function (7) & remain in stop mode.

2) Press the “ INFO “ function and the LCD display will show the default bitrate (128

Kbps)

3) Press skip or buttons (7) to select the desired bitrate for encoding.

4) Press again the “ INFO “ to confirm the setting and the lcd display (2) resume to “

phono “ mode

REMOVING OF USB / MEMORY CARD

To remove the USB / MEMORY CARD, turn off the power or switch the function mode to

either AUX or TUNER first. For USB port – un-plug it by pulling out the USB socket directly,

for memory card – press the memory card inward & then release, now the card being

partially eject and you can remove it by hand.

LINEOUTCONNECTION

You can connect the system to your home Hi-fi system by connecting the LINE OUT socket

(27) to the auxiliary input socket with a RCA cable (not included).

9 10

SPECIFICATIONS

Power Supply

AC: 230V ~ 50Hz

RC Battery: 2 x AAA(UM-4) 1.5V (not included)

Radio Frequency Coverage

FM: 87.5 - 108MHz

MW: 522 - 1620kHz

Power output 2 x 2 W RMS (10% THD)

Design and specifications are subject to change without notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roadstar TTR-8632UCEN Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info