Bedienungsanleitung Robbe Futaba FX-40 (Seite 78 von 105) (Englisch)

520094

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

Model menu

Gyro settings

FX-40

18.13 GYRO SETTINGS

If you wish to use a gyro in a fixed-wing model air

craft in order

to stabilise one flight axis, this is the menu you use for entering

the settings for the gyro. The basic purpose of this menu is to

allow the pilot to adjust gyro gain (sensitivity) from the trans-

mitter for a maximum of three gyros - i.e. one for each primary

axis of the model aeroplane.

Gyro gain can simply be programmed as a percentage value,

but it is also possible to select the gyro type. You can assign a

switch which is used to set the gain to any of three values from

the transmitter. As with many functions, it is also possible to

determine whether the settings are to apply to all flight modes

(Glob) or only to the currently activated flight mode (Sepa).

Mark the ‘Gyro’ option in the Model menu. The screen now

looks like this:

The menu features three identical levels which are used to

enter three different gain levels (Rates 1 - 3). This function

must first be activated in the Status line in the usual way by

marking the appropriate field; the field will then switch to ‘ON’

or ‘OFF’, according to the position of the switch. Please note

that this only occurs if you have assigned and activated a

channel for adjusting gyro gain in the ‘Function’ menu of the

Base menu (Section 16.7).

In the ‘Type’ column you should enter the type of gyro installed

in the model. For AVCS or ‘heading hold’ gyros enter ‘GY’ as

the type; for others select the ‘NORM’ type. In the ‘Switch’

column you can select a switch and its direction of operation

using the familiar procedure. The default setting is ‘NONE’, i.e.

the function is constantly switched on. The effects and

method of setting the ‘Glob’ or ‘Sepa’ mode have already

been described; the settings are adjusted at far right on the

screen.

The fields for setting the gain levels for the (max.) three gyros

are grouped together in a separate field. If you have entered

‘GY’ as gyro type, you have the option of choosing whether it

is to work in normal (NOR) or ‘AVCS’ mode; this applies to

each gyro separately. For more information on this, please

refer to the instructions supplied with the gyro you are using.

The gain for the three (possible) gyros is entered in the usual

way as a percentage value, with the help of the arrow buttons.

In each case the adjustment range is 0% to 100%; the default

setting is 0%. Pressing the ‘Reset’ field restores the default

setting.

This screen shot shows a sensible programming set-up for the

Gyro function.

You should program a gain value for each gyro installed in your

fixed-wing model aircraft. Currently this setting is not effective,

as switch ‘D’ is in the ‘OFF’ position. This state is displayed In

the Status field.

Gyro 1 is a normal gyro, and the gain setting you can call up is

set to 30%. Gyro 2 is working in heading-hold mode with a

pre-set of 20%. The third gyro is also a heading-hold gyro,

with a switchable sensitivity of 30%. In our example the set-

tings apply to all flight modes.

For a more complex model aircraft equipped with two aileron

servos and a triple-axis stabilisation system, the following set-

tings would be typical:

Gyro 1 (GYA351) channel 7, gyro 2 (GYA352) channel 8, gyro 3

(GYA352) channel 9 (these channel assignments are set in the

Function menu)

RATE 1: OFF; GY; SW-E; GRP; NORM (60%); NORM (60%)

NORM (60%)

RATE 2: INH; GY; NONE; GRP; AVCS (0%); AVCS (0%); AVCS

(0%)

RATE 3: OFF; GY; SE-E; GRP; AVCS (60%); AVCS (60%);

AVCS (60%)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba FX-40 Seite 78

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robbe Futaba FX-40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info