Bedienungsanleitung Robbe Futaba FX-40 (Seite 98 von 105) (Englisch)

520094

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

Model menu

Flight mode hold

Notes on the stopwatch

FX-40

19.12 FLIGHT MODE HOLD

The purpose of this function is to enable you to carry out

adjustments in another flight mode. The motor is held at idle to

prevent the possibility of opening the thr

ottle accidentally. The

‘Flight mode hold’ function can only be activated in ‘Normal’

flight mode, and even then only if the throttle stick is at the idle

position.

A warning signal sounds as soon as you activate ‘Flight mode

hold’. In this way the transmitter alerts you to the fact that the

motor will not respond if you move the throttle stick. You can

now change to a different flight mode by operating the appro-

priate flight mode switch, and make changes to the settings in

that flight mode.

When you activate this function, the throttle servo is fixed at a

pre-set position. If you wish to change the settings for the

channel which operates the throttle servo, you must first disa-

ble the ‘Flight mode hold’ function.

Note that the ‘Flight mode hold’ function cannot be activated

or disabled if:

• a flight mode switch is switched on, or

• the throttle stick is at a value higher than 1/3 of full stick travel.

This option is controlled from the base display for model heli-

copters. To define the pre-set value, mark the field and move

the throttle stick to the desired position. Note that the stick

must be positioned at a point lower than 1/3 of full travel.

The base display shows the status of this option in the follo-

wing way:

‘ON’: Flight mode hold switched on

‘INA’: Flight mode hold switched off (inactive)

The two screen displays below show these states:

19.13 NOTES REGARDING THE STOPWATCH WHEN USED

WITH THE ‘HELICOPTER’ MODEL TYPE

When the ‘Helicopter’ model type is selected, ther

e is a dif

fe-

rence in the way the two stopwatches are displayed on-

screen. The function of the timers has already been described

in full in the Base menu (Section 16.15, page 50, Part 1 of

these instructions), but the screen shot of this function related

to a powered fixed-wing model aircraft.

When you activate the ‘Helicopter’ model type, the main dis-

play normally shows the throttle position and the collective

pitch setting instead of the second stopwatch, as these para-

meters are vital for proper control of a model helicopter.

If you need to see the second stopwatch, you must activate

the ‘Stopwatch’ option in the Base menu for helicopters. The

screen display now looks like this:

In the bottom line of the frame for Stopwatch 2 you will find an

additional switch field labelled ‘Start display’. If you mark this

field, you can opt to include the second stopwatch in the main

display instead of the throttle position / collective pitch setting.

When you mark the field, the label changes to ‘On’; both

timers are then shown in the main display, as with a powered

fixed-wing model.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba FX-40 Seite 98

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robbe Futaba FX-40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info