Bedienungsanleitung Robbe Futaba T-12 FG (Seite 38 von 128) (Englisch)

467096

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

5. Idle down setting

The idling speed can be lowered with one touch by

a switch without changing the throttle trim position.

Perform this setting with the Idle Down function of the

Linkage Menu. After activating the Idle Down function

and selecting the switch, adjust the idle down speed.

For safety, the idle down function acts only when the

throttle stick is slow side.

*While the Throttle Cut function is in operation, the Idle

Down function does not work.

6. AFR (D/R)

AFR function is used to adjust the throw and

operation curve of the stick, lever, and switch functions

&+WR&+DQG9WR9IRUHDFKÀLJKWFRQGLWLRQ

This is normally used after End Point (ATV) has

GH¿QHGWKHPD[LPXPWKURZGLUHFWLRQV

7. Airbrake

This function is used when an air brake is necessary

when taking off or diving, etc.

The preset elevators and flaps (camber flap, brake

ÀDSRIIVHWDPRXQWFDQEHDFWLYDWHGE\DVZLWFK

7KHRIIVHWDPRXQWRIWKHDLOHURQHOHYDWRUDQGÀDS

servos can be adjusted as needed. Also the speed of the

DLOHURQHOHYDWRUDQGÀDSVHUYRVFDQEHDGMXVWHG,1

side/OUT side) A delay can be set for each condition,

and a Cut switch which will turn OFF the delay can be

chosen. Trim amounts can be fine-tuned by setting a

VR. You can also set the Auto Mode, which will link

Airbrake to a stick, switch, or dial. A separate stick

VZLWFKRUGLDOFDQDOVREHVHWDVWKH212))VZLWFK

$GGLWLRQRIÀLJKWFRQGLWLRQV

7KHWUDQVPLWWHUFDQLQVWDOOXSWRHLJKWÀLJKWFRQGLWLRQV

per model. You can assign all switches including sticks,

VZLWFKHVWULPOHYHUVDQGWULPVZLWFKHVDVÀLJKWFRQGLWLRQ

VHOHFWLRQVZLWFKHV<RXFDQDOVRDGGGHOD\HGPL[LQJ

to these functions in order to avoid sudden changes.

0RUHRYHU\RXFDQVHWSULRULW\RUGHUIRUÀLJKWFRQGLWLRQV

when you set more than one condition. In addition, you

can copy conditions and/or change names of conditions.

7KLVFRPPDQGPD\DOVREHXVHGWRGH¿QHZKDWVZLWFKHV

DQGRUFRQWUROVDUHXVHGWRDFWLYDWHHDFKÀLJKWFRQGLWLRQ

The Condition Select function automatically allocates

the Condition 1 for each model type. Condition 1 is

WKHGHIDXOWFRQGLWLRQDOVRUHIHUUHGWRDV1RUPDODQGLV

the only one active when a new model type is defined.

This condition is always on, and remains on until other

conditions are activated by switches.

The Condition Delay can be programmed for each

channel. The Condition Delay is used to change the

servo throw smoothly when switching conditions.

*When a new condition is added, "Condition1" data is

automatically copied.

*Select the condition switch and set the new condition data in

WKHVZLWFK21VWDWH+RZHYHULIWKHJURXSPRGH*5283

was selected in advance, the same data will be input at all the

FRQGLWLRQV6HOHFWWKHVLQJOHPRGH6,1*/(DQGDGMXVWWKH

condition you want to change.

9. When tailless wing model selected

Tailless wing elevator operation uses elevator to camber

PL[LQJ7KLVIXQFWLRQFDQQRWEHSHUIRUPHGDWLQLWLDOVHWWLQJ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba T-12 FG Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robbe Futaba T-12 FG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info