Bedienungsanleitung Robbe Futaba T6EX (Seite 18 von 38) (Englisch)

747912

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

TRIM Trim Settings

There are four trim levers (“trims”) on the front of the transmitter. Three of the trims are for adjusting the neutral position of the

aileron, elevator and rudder servos. The fourth trim is for setting the idle r.p.m. of the engine when the throttle stick is all the

way down. The intended use of the trims is to make small servo adjustments, in ﬂight, to get the model properly “trimmed” (so

it will ﬂy straight-and-level). Because the trims are intended to be used while the model is in ﬂight, you do not have to “enter

the program” to adjust the trims. Simply push or pull on the trim levers while ﬂying and the neutral position of the servos will

shift. Keep in mind that you should start out with the control surfaces centered when the servos are centered and the trims are

“zeroed” (or near zero).

THEN you can adjust the trims once airborne.

Center the servos:

1. Turn on the transmitter and receiver. Operate the controls to make sure the servos respond in the correct direction. Use the

reversing function to reverse any servos necessary.

2. Center the throttle control stick.

3. Place the servo arms on the servos so they are perpendicular to the pushrods (see page 8). It is okay to cut off any unused

servo arms.

4. Connect the pushrods to the control surfaces. Adjust the length of the pushrods until the control surfaces are centered when

the servos are centered.

Note: The throttle trim affects the throttle servo only when the throttle stick is below “1/2 stick.” This way, the ﬁnal closing of

the carburetor can be adjusted without affecting the servo throughout the rest of the range.

To adjust the trim settings:

Once the servos and control surfaces have been connected and the control throws have been set using the end points and

dual rates, get the model airborne. Adjust the trims as necessary to get the model to ﬂy straight-and-level. If much trim is

required on any one control it is a good idea to readjust the pushrods so the trims can be returned to neutral (zero). Adjusting

the trims with the trim levers changes the servo’s position in increments of “4.” If finer adjustments are required, land the

model, then enter the program as described below to adjust the trims in increments of “1.”

1. Enter the programming mode and use the MODE key to activate the TRIM menu.

2. Press the SELECT key to display the channel to be adjusted (the figure shows trim

adjustment for CH1).

3. Adjust the trim using the DATA INPUT lever. Note that initially, the values change in

increments of “1,”but if the DATA INPUT lever is held long enough the values will change

more rapidly.

4. Repeat the steps for other channels that require trim adjustments.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba T6EX Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info