Bedienungsanleitung Robbe Futaba T6EX (Seite 24 von 38) (Englisch)

747912

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

N-TH Normal throttle curve function (HELI only)

Used to set throttle curve for normal ﬂight. 5-point throttle curve is utilized to best match the blade collective pitch to the engine

RPM for consistent load on the engine. Throttle curve can be adjusted from 0-100% each point.

This normal throttle curve creates a basic curve for hovering. Use this function together with the normal pitch curve (see

Normal pitch curve) so that up/down control has a constant engine speed.

To set the normal throttle curve:

1. Enter the programming mode and use the MODE key to access the

“N-TH” function.

Throttle stick position number will appear on left side of display and “%” symbol will be

ﬂashing.

2. Use SELECT key to select the desire curve point. Point 1 is shown initially which is throttle

stick all the way downward (slow) position. Point 5 is throttle stick all the way upward (hi)

position.

3. Push up or down DATA INPUT lever to set the servo position.

4. Use SELECT key to set other points in same manner.

N-PI Normal pitch curve function (HELI only)

Used to set pitch curve for normal ﬂight. 5-point pitch curve is utilized to best match the blade collective pitch to the engine

RPM for consistent load on the engine. Pitch curve can be adjusted from 0-100% each point.

This normal pitch curve creates a basic curve for hovering. Use this function together with the normal throttle curve so that up/

down control has a constant engine speed.

To set the normal pitch curve:

1. Enter the programming mode and use the MODE key to access the “N-PI” function. Throttle

stick position number will appear on left side of the display and “%” symbol will be ﬂashing.

2. Use SELECT key to select the desired curve point. Point 1 is shown initially, which is throttle

stick all the way downward (slow) position. Point 5 is throttle stick all the way upward (hi)

position.

3. Push up or down DATA INPUT lever to set the servo position.

4. Use SELECT key to set other points with same manner.

I-TH Idle-up throttle curve function (HELI only)

Used to set throttle curve for idle up ﬂight. 5-point throttle curve is utilized to best match the blade collective pitch to the engine

RPM for consistent load on the engine when idle up function is on. Throttle curve can be adjusted from 0-100% each point.

This idle up throttle curve is to set consistent engine RPM and can be activated at any time when mid air maneuvers are

executed, such as loops, rolls, and 3D ﬂight, even when the blade collective pitch is reduced.

To set the idle-up throttle curve:

1. Enter the programming mode and use the MODE key to access the “I-TH” function.

2. Push the DATA INPUT lever upward for 0.5 seconds. This will cause the flashing

“INH”

display to change to a ﬂashing

“OFF” or “ON” display. Now the I-TH function is on. Push

the SELECT key, and throttle stick position number appears on left side of display and “%”

blinks. (“OFF”: if the idle-up switch is off, “ON”: if the idle-up switch is on.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba T6EX Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info