Contents and Technical Specications
(Specications and ratings are subject to change without notice.)
Your 8FGA/8FGH/8FG includes the following components:
• T8FGA, T8FGH or T8FG Transmitter
• R6008HS Receiver
• HT6F1700B Ni-MH battery & Charger
• Switch harness
• Neck strap
*The set contents depend on the type of set.
Transmitter T8FGA/T8FGH/T8FG
(2-stick, 8-channel, FASST-2.4G system)
Transmitting frequency: 2.4GHz band
Modulation: 2.4G 7-ch or 2.4G Multi-ch, switchable
Power supply: 7.2V HT6F1700B Ni-MH battery
Receiver R6008HS
(FASST-2.4G system, dual antenna diversity)
Power requirement: 4.8V or 6.0V battery or regulated
output from ESC, etc. (*1)
Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)
Weight: 0.48 oz. (13.5g)
(*1) When using ESC's make sure that the regulated
output capacity meets your usage application.
(Suggested Servo for use with your 8FG system)
Servo S9252 (Digital servo)
Control system: Pulse width control, 1.52 ms neutral
Power requirement: 4.8 V (from receiver)
Output torque: 91.7 oz.-in. (6.6 kg-cm) at 4.8V
Operating speed: 0.14 sec/60 at 4.8V
Size: 1.57 x 0.79 x 1.44 in. (40 x 20 x 36.6 mm)
Weight: 1.76 oz. (50 g)
Servo S9255 (Digital servo)
Control system: Pulse width control, 1.52 ms neutral
Power requirement: 4.8 V (from receiver)
Output torque: 125.0 oz.-in. (9.0 kg-cm) at 4.8V
Operating speed: 0.16 sec/60 at 4.8V
Size: 1.57 x 0.79 x 1.44 in. (40 x 20 x 36.6 mm)
Weight: 1.94 oz. (55 g)
Servo S3151 (Standard, Digital servo)
Control system: Pulse width control, 1.52 ms neutral
Power requirement: 4.8 V (from receiver)
Output torque: 43.1 oz.-in. (3.1 kg-cm) at 4.8V
Operating speed: 0.21 sec/60 at 4.8V
Size: 1.59 x 0.79 x 1.42 in. (40.5 x 20 x 36.1 mm)
Weight: 1.48 oz. (42 g)
Servo S3001 (Standard, ball-bearing)
Control system: Pulse width control, 1.52 ms neutral
Power requirement: 4.8 - 6.0V (from receiver)
Output torque: 41.7 oz.-in. (3.0 kg-cm)
Operating speed: 0.22 sec/60
Size: 1.59 x 0.78 x 1.41 in. (40.4 x 19.8 x 36 mm)
Weight: 1.59 oz. (45.1g)
Usage condition on "High Speed mode"
(R6008HS)
CAUTION
When using the R6008HS in the high speed
(HS) mode, digital servos are required for
the rst six channels (1-6).
If an analog servo is connected to one of the first
six channels when in the high speed mode, the
servo will not function properly. Additionally,
while many peripheral devices will operate in either
the high speed or normal mode, some will not. If
there are any difficulties noted, please return the
reciever's operational mode to the "Normal" mode
to determine if this resolves the difculty.
If using the R6008HS in the high speed mode,
analog servos may be used for channels seven and
eight.
(For Operation Mode Selection, see p.25)
