77
<Model Menu (Common Functions)>
Touch the RTN button to end adjustment and
return to the cursor mode.
*Needle high trim works as high trim based on the center.
(Works like ATL trim.)
●Acceleration setting (Airplane)
*This function is used to adjust the needle/engine rise
characteristics during acceleration. This enables an
acceleration function which temporarily increases the needle
operation from the throttle stick.
This function is used when there are symptoms of the
mixture being too lean or too rich, which would be
generated by sudden throttle stick inputs.
[Acceleration rate setting (RATE)]
*Acceleration can be adjusted for at both high and low
settings.
[Damping rate setting (DUMPING)]
*The return time after operation (Dumping) can be set.
Move the cursor to the rate item you want to
change and touch the RTN button to switch
to the data input mode.
Adjust the rate by scrolling the touch sensor.
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
Touch the RTN button to end adjustment and
return to the cursor mode.
[Operation point setting (ACT POS)]
*The operation point at which the acceleration setting will
occur. If this point is exceeded, acceleration is performed.
Move the cursor to the [ACT POS] item and
hold the throttle stick to the position you
want to change and touch the RTN button
for one second.
Note: When using the acceleration funtion,
since the needle stroke is large, adjust your
settings so there is no binding of your linkage.
●Engine cut setting
* Operation linked with the throttle hold function, throttle cut
function, and idle down function is possible. The throttle cut
position can be adjusted accordingly. Set it to the full closed
position.
Move the cursor to the throttle cut or idle
down item and touch the RTN button to
switch to the data input mode.
Adjust the servo position by scrolling the
touch sensor.
Initialvalue:THRCUT:17%,IDLEDOWN:0%
Adjustment range:THR CUT: 0~50%, IDLE
DOWN:0~100%
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
Touch the RTN button to end the adjustment
and return to the cursor mode.
Setting method
*Before using this function, assign the [FUEL MIX] function
to an unused channel in the Linkage menu [FUNCTION]
function.
●Activate the function.
1. Move the cursor to the [ACT] item and touch
the RTN button to switch to the data input
mode.
Select the ACT mode by scrolling the touch
sensor.
*The display blinks.
Tou ch the RTN butt on to activ ate the
function and return to the cursor mode. (ON
is displayed.)
2. Move the cursor to the [MIX] item and touch
the RTN button to switch to the data input
mode.
Select the mixing mode you want to change
by scrolling the touch sensor.
*The display blinks.
Touch the RTN button to change the mode
and return to the cursor mode.
*When [MIX] is selected at the [MIX] item, the throttle curve
setting data becomes the mixing master side data. When
[UNMIX] is selected, the throttle stick position becomes the
mixing master.
●5-point curve setting
1. Move the cursor to the point rate setting item
you want to adjust and touch the RTN button
to switch to the data input mode.
Adjust the rate by scrolling the touch sensor.
Initialvalue:0%
Adjustmentrange:-100%~+100%
*When the RTN button is touched for one second, the servo
operation position is reset to the initial value.)
Touch the RTN button to end adjustment and
return to the cursor mode.
2. Repeat this procedure for each point.
●Needle high trim setting
1. Move the cursor to the needle high trim
selection item and access the switch setup
screen by touching the RTN button. Select
the needle high trim lever.
*For a detailed description of the setting method, see [Switch
Setting Method] at the back of this manual.
2. Move the cursor to the TRIM rate item and
touch the RTN button to switch to the data
input mode.
Adjust the trim rate by scrolling the touch
sensor.
Initialvalue:0%
Adjustmentrange:-30%~+30%
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
