Bedienungsanleitung Robbe Power Peak A4 EQ-LCD - 8559 (Seite 11 von 48) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

577499

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Table of contents

Power Peak® A4 EQ-LCD

No.

8559 / 8560

Dear customer,

Thank you for purchasing the 12V DC Power

Peak

A4 EQ-LCD rapid charger from the robbe

range. Although the charger is extremely easy to

use you should, nevertheless, take care to thor-

oughly read the operating instructions and safety

information before using your new charger.

Safety Information

The Power Peak

A4 EQ-LCD is designed

for charging rechargeable lithium and NiMH

batteries. Due to the risk of explosion, do not use

the charger to charge dry batteries.

Never place the charger and connected

batteries on combustible surfaces. Never

use the charger in the vicinity of combustible

materials or gases.

• The charger is designed for operation only for

11...15V DC operation, therefore, never ope-

rate the charger with a different voltage rating.

• Protect the charger from dust, dirt and mois-

ture.

• Do not expose the charger to excessively low

or high temperatures as well as direct sun-

light.

• Make sure the Power Peak

A4 EQ-LCD

charger is not exposed to impact, pressure or

excessive vibration load.

• Do not leave the charger unattended during

operation. The charger can heat up consi-

derably during normal operation.

• Ensure the cooling openings are always clear

to allow air to freely circulate (never place on

carpeted or felt surfaces).

• When not used for a longer period of time,

unplug the charger from the power source

and disconnect any batteries.

• Do not charge rechargeable batteries twice in

quick succession.

• Do not charge batteries that are at a high tem-

perature.

Allow batteries to cool down to ambient tem-

perature.

• Only cells of the same capacity and of the

same make may be charged together.

• Never charge two batteries connected in par-

allel to one output, connect only one rechar-

geable battery pack at a time.

• Ensure correct polarity of the battery and

avoid short-circuits .

• Closely follow the instructions provided by the

battery manufacturer.

• Check for damage to the casing and leads.

Note:

Pay particular attention to the safety instruc-

tions provided by the battery manufacturer.

2. General Description

The Power Peak

A4 EQ-LCD is an inexpensive yet high quality 12V DC rapid charger in a metal cas-

ing for charging 1...4-cell 3.7 Volt LiPo batteries and 4...8-cell NiMH batteries with integrated equalizer

and large LC display showing current, voltage and capacity. The number of cells in LiPo batteries is

identified automatically.

The charging current can be set in the range from 300 to 3,000mA. The recommended charging rate

is 1C (battery capacity = charging current), please refer to ‚Charging the Battery‘.

The charging progress and the end of charging are indicated by the status LED and the beeper.

By connecting to the power supply unit, which is included in delivery specification No. 8560, the

charger can be operated from the 230 Volt mains power supply, thus making it a 230 V AC and 12 V

DC charger.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Power Peak A4 EQ-LCD - 8559 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robbe Power Peak A4 EQ-LCD - 8559

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info