Bedienungsanleitung Robland HX260 (Seite 25 von 98) (Deutsch, Englisch)

625545

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

24 V0212 HX SERIES

– English

– Deutsch

Adjusting the spindle height (g. 18)

1 Unlock the locking lever (3) by turning it to the left.

2 The spindle arbour can be raised or lowered using the hand wheel (4).

3 After height adjustment always secure the spindle arbour by locking the lever (3) by turning it to

the right.

Remark: When, after intensive use of the locking lever (3), it is no longer possible to lock this lever, take

off the nut and remove the lever. Then turn it 1/6 turn to the right before putting it back on again. Put the

nut back on and tighten it.

The spindle fence

Working with the spindle fence (fig. 19)

The spindle fence is tted onto the table with two locking knobs (1). The body of the spindle fence is

equipped with two slots which enables front and back movement. When the fence is tted onto the

table, the position of the aluminium fence plates can be adjusted by means of the adjustment knob

(2). The opening of the 2 fence plates goes like follows: loosen the wing nut (3) which hold the fence

and move the fence towards each other, so there is a minimal gap between the protruding tool and the

fence plates. It is advisable to use a false fence or integrated fence which is mounted between the 2

spindle fences. The adjustment of the fences can be checked with a at and precise rule.

Before starting the machine, the blocking of the bars of the fences on the table has to be checked. The

wood pushers exert vertical and horizontal pressure on the work piece, which pushes the work piece

against the table and the fence and which makes it slide easily. The manual wood pusher (g. 20),

supplied with the machine, can be used to push the wood safely. Not one element is xed on the useful

table surface. The 10 mm space between the base of the horizontal wood pusher and the table makes

it possible to move the wood pusher under the wood pushers. To replace the spindle tool, or to make

use of the feeder, the whole pusher system can be cleared by ipping it over to the back of the spindle

fence: Pull the lever in the direction of the arrow. Lift up a little the cover plate. Now the system can

be ipped over to the back. This part will prevent the fences from falling down. It is advisable to use a

feeder system, as the kick back usually happens whilst working with the spindle fence when only a part

of the piece is machined.

Clean apparatus make adjustment easier. Fences in a perfect state are advisable for quality work.

Therefore, they should be replaced when the edge or surface is damaged by the spindle tool.

Adjustments (g. 20)

3 adjustments have to be made:

– Adjustments of the spindle fences as close as possible tot the outer tool diameter, and adjustment

of the depth of cut.

– Adjustments of the vertical pusher according to the height of the work piece

– Adjustments of the horizontal pusher according to the width of the work piece

– There can ‘t be too much pressure on the pushers, so the wood can slide easily between the wood

pushers and the fences

Important:

Before starting the spindle, all locks and settings should be checked, and check manually if the tools

can rotate freely. Always use the supplied wood pushers on the fence. This upper cover plate is used as

protection of the upper part of the spindle tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robland HX260 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robland HX260

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info