Bedienungsanleitung Roblin Crystal Electro (Seite 11 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

490288

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

- 3 metres with 2 x 90° bends.

- 2 metres with 3 x 90° bends.

The above assumes our 150 mm (6 INS) ducting is being installed. Please note ducting components

and ducting kits are optional accessories and have to be ordered, they are not automatically sup-

plied with the chimney hood.

IN THE EXTRACTION MODE:

a. Connect the ducting 150mm (6 INS) over the round outlet item 6 on top of the canopy and secure

the connections with appropriate clamping rings or adhesive tape (Fig. 5).

b. Remove the grease lters (see paragraph Maintenance) being sure that the connector of the mains

cable is correctly inserted in the socket placed on the side of the fan. Before tting the chimney to

the canopy make the electrical connection as described in the section titled ELECTRICAL. When

the electrical connection has been made, test the lights and the fan motor.

c. Upper chimney stack

•Slightly widen the two sides of the upper chimney stack (Fig.5 - Item 7a) and hook them behind the

brackets item 2 making sure that they are well seated.

•Secure the sides to the brackets using the 4 screws 12c (2,9 x 9,5) supplied.

d. Lower chimney stack

•Place the black frame (Fig. 1, rep. 9 ) on the body of the hood at the bottom of the telescopic chimney.

•Slightly widen the two sides of the chimney stack (Fig. 5 - Item 7b) and hook them between the upper

chimey stack and the wall, making sure that they are well seated.

IN THE RECIRCULATION MODE:

a. Fit the recirculation spigot bracket item 4 onto the upper chimney wall bracket using the same xing

screws (Fig.7 - item 2).Put the spigot item R into the spigot bracket item 4• Insert the connection

extension pieces laterally item G in the spigot. Make sure that the outlet of the extension pieces

item G is horizontally and vertically aligned with the chimney outlets.

b. Connect the ducting 150mm (6 INS) not provided between motors item 6 and the recirculation spigot

and secure the connections with appropriate clamping rings or adhesive tape.

c. Remove the grease lters (see paragraph Maintenance) being sure that the connector of the feeding

cable is correctly inserted in the socket placed on the side of the fan. Before tting the chimney to

the canopy make the electrical connection as described in the section titled ELECTRICAL. When

the electrical connection has been made, test the lights and the fan motor.

d. Remove the metal grease lters and insert the charcoal lter into the base of the motor housing and

secure the lter with two metal securing straps item A as illustrated in Fig. 8.

e. Upper chimney stack

•Slightly widen the two sides of the upper chimney stack (Fig.7 - Item 7a) and hook them behind the

brackets item 2 making sure that they are well seated.

•Secure the sides to the brackets using the 4 screws 12c (2,9 x 9,5) supplied.

f. Lower chimney stack

•Place the black frame (Fig. 1, rep. 9 ) on the body of the hood at the bottom of the telescopic chimney.

•Slightly widen the two sides of the chimney stack (Fig. 5 - Item 7b) and hook them between the upper

chimey stack and the wall, making sure that they are well seated.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roblin Crystal Electro Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info