Bedienungsanleitung Roblin Cube 600 (Seite 10 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

490284

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

markings identifying the terminals in your plug, proceed as follows.

- The wire which is coloured green and yellow must be connected to the terminal in the plug which is

marked with the letter E or by the earth symbol or coloured green or green and yellow.

- The wire which is coloured blue must be connected to the terminal which is marked with the letter N

or coloured black.

- The wire which is coloured brown must be connected to the terminal which is marked with the letter

L or coloured red.

ATTENTION: Do not forget to use adequate plugs to the support brackets. Enquire after the manu-

facturers. Do an embedding if necessary. The manufacturer accepts no responsibility in case of a

faulty hanging due to the drilling and the setting up of plugs in the ceiling.

1) Unpack the hood parcel.

• LAYING OUT BEFORE FITTING THE HOOD

2) Mark the centre of the cooking appliance onto the ceiling with a plumb line. Draw the horizontal axes

running parallel to the stove top onto the ceiling as illustrated Fig. 1.

3) Place the drill gauge centred on the axes aligning the axes on the drill gauge centrally over these

axes as illustrated Fig. 1.

Mark the positions on the ceiling for : - The cut-out for the ducting Ø 150 mm in the extraction

mode and Ø 200 mm in the remote mode when ducting runs through the ceiling.

- The mains supply cords.

- The 8 xing holes for Ø 10 mm nuts and bolts.

Drill the different holes with the appropriate masonry bit. When xing the cooker hood to a plasterboard

ceiling ensure it is reinforced as illustrated in Fig. 2 and attach using four Ø10mm nuts and bolts; ensuring

the bolts as sleeved between the plasterboard and the joist supports to prevent the ceiling being damaged

when the bolts are tightened up.

If the ceiling is concrete, use eight Ø 10 mm steel rawl bolts. Plastic rawl plugs must not be used.

4) Draw a vertical line onto the wall from the centre of the cooking appliance up to the ceilling, using a

spirit level and a marker pen as illustrated in Fig. 1 - item 1. This is to ensure the correct alignment

of the chimney hood.

5) Drilling xing holes 2 (Fig. 1 ):

Mark a point on the vertical line at a distance from the cooking appliances of:

d = 650 + 51 = 701 mm (Measurement without splashback).

The distance H is the minimum height in mm from the cooking appliances to the bottom edge item 3 of

the front panel of the hood.

At the point marked, draw a horizontal line parallel to the cooking appliances. Drill 4 holes 2 in the wall

using an 8 mm drill bit and insert the rawl plugs into the holes. Fix the brackets item 2, using the 4.2

x 44.4 mm screws 12a and rawl plugs supplied. Small adjustments can be made using the hood

adjustment screws (see Fitting the canopy Fig. 10.1 & 2).

6) Aligning its centre on the vertical line, mark the 4 eyelet holes of the upper canopy bracket onto the

wall about 448 mm from the ceiling or from the upper limit. Drill the holes for the xing bracket using

an 8 mm masonry bit.

7) Fixing the canopy: Before starting to x the canopy it will be necessary to follow the instructions Fig.

3 to 9.

The height of the cooker hood can be adjusted in 53 mm stages. 650 mm when tting above an electric

hotplate and 700 mm when tting above a gas hotplate. Select the height required using the measure-

ments illustrated in Fig. 9 and x the metal diffuser to the frame of the chimney brackets using the height

5 x 10T hexagonal headed screws. A drawing on the drill gauge denes the positioning for the controls.

8) Place the canopy onto the wall brackets and x it to the ceiling as illustrated in Fig. 10.1.

Attention: 2 persons are necessary to secure this operation.

And then follow the instructions Fig. 10.1 & 2.

9) Check the vertical of the chimney.

10) Ducting:

The hood is more effective when used in the extraction mode (ducted to the outside). When the cooker

hood is ducted to the outside, charcoal lters are not required.The ducting used must be 150 mm (6

INS), rigid circular pipe and must be manufactured from re retardant material, produced to BS.476

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roblin Cube 600 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info