Bedienungsanleitung Roblin Declic 609 (Seite 9 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

490315

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

B -REMOTE INSTALLATION OF THE DECLIC WITH CONFORT PRO OR MISTRAL 800 MOTOR

See the specic instruction booklet supplied when tting the remote controlled Confort or Mistral 800

motorat a distance from the Declic extractor hood.

1.Turn the screws anticlockwise to loosen the 2 xing clips on the Declic (g 1).

2.The Declic is supplied with a 10mm and 20mm spacer to ll the gap between the wall and the rear

ofthe extractor. To t the spacer unscrew the screws located between the halogen lights and remove

thefront light housing in order to access (g.5).

3.Cut the require aperture in the base of the kitchen cabinet as indicated (g. 6).

4.Insert the telescopic extractor in the aperture in the kitchen cabinet and turning the screws clockwis-

esecure the assembly to the kitchen cabinet (g 1).

5.Insert the grommets into the screw holes (g 8).

6.Connect the ducting onto the round outlet on the top of the motor assembly.

7.Connect both appliances together (g 9) and connect them to the mains supply

(See ELECTRICALWIRING chapter).

CAUTION : If the kitchen cabinet does not have a door you must execute points 6 and 7 before-

point 4.

C -REPLACING THE DECORATIVE FRONT STRIP

You can replace the strip in the front trim with a matching strip of kitchen furniture nish or with a com-

pletepiece of cornice.

1.Remove the glass (See chapter 6: MAINTENANCE).

2.When replacing the front strip with matching laminate. Firstly, remove the right-hand end capping

fromthe front trim and slide out the aluminium front strip plate. Secondly, insert the cut piece of

laminateand replace the right-hand end capping.

3.When replacing the whole front trim with a piece of lighting pelmet or similar. Firstly, remove the right-

hand end capping and the aluminium strip to access to the front xing screws. Secondly, cut the

newfront trim in accordance with the dimension contained in g.14 and machine nish the new strip

beforexing the trim and metal plate using the original screws (g.15).

4 OPERATION

Access to the functions by opening of the side.

•Lighting : By rock-switch ON / OFF ( Fig. 16 ).

• Motor : By dimmer switch ( Fig. 17).

Automatic stop of the functions by closing of the side.

5 USEFUL HINTS

• To obtain the best performance we recommend you to switch ‘ON’ the cooker hood a few minutes (in

the boost setting) before you start cooking and you should leave it running for approximately 15 minutes

after nishing.

• IMPORTANT: NEVER DO FLAMBÉ COOKING UNDER THIS COOKER HOOD

• Do not leave frying pans unattended during use as over-heated fat and oil might catch re.

• Do not leave naked ames under this cooker hood.

• Switch ‘OFF’ the electric and gas before removing pots and pans.

• Ensure heating areas on your hotplate are covered with pots and pans when using the hotplate

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roblin Declic 609 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info